Wood master Flex Fuel Скачать руководство пользователя страница 29

Страница: 29 / 76

March 2011

Flex Fuel Owner’s Manual

9.5 Setting the Clock/Date

Note: There is no automatic conversion for daylight saving time.

Note: This furnace runs on DD/MM/YY date format and on military time format.

Once you have selected this menu item, the clock stops and the following figure appears on the screen.

9.6 Service Menu

The service menu includes factory settings designed to provide ideal combustion characteristics. These

settings have already been optimized in the factory. Access to these settings can only be obtained by

your dealer. Please contact your WoodMaster Flex fuel Dealer for assistance.

9.7 Alarm Protocol

All malfunctions are chronologically listed in the alarm protocol. The alarm protocol menu can be found

in the service menu main page and selecting it will bring up the following screen:

When pressing the control knob on the alarm protocol screen, the symbol LEFT/RIGHT appears in the

upper right hand corner and all previous alarms can be scrolled through.

Note: 40 entries are stored. After the 40th entry (alarm number 39), the oldest entry with alarm

number 0 is deleted. It will store when the error message was triggered and when it was cancelled.

Therefore, there are 2 entries in the alarm protocol per error message.

9: Basic Furnace Settings

Set CLOCK/DATE

Date: 10.09.10
Time: 17:05

ALARM PROTOCOL

Alarm number: 37

Type of alarm: acknowl.

Date: 10.12.09

Clock: 10:20:27

SAFETY TEMPERATURE LIMITER

HAS TRIPPED!

Please reset the safety

temperature limiter once the

boiler has cooled down

then press START!

ALARM PROTOCOL

Alarm number: 30

Type of alarm: triggered

Date: 10.12.09

Clock: 10:10:13

MAIN FUSE FAULTY!

Follow the instructions in the

operating manual and replace

the main fuse!

The boiler will be operational

again once its run-on time has

expired!

Содержание Flex Fuel













































































Результаты поиска

Содержание Flex Fuel

Отзывы:

Похожие инструкции для Flex Fuel

Бренды по названию

Популярные бренды

Wood master Flex Fuel, Руководство пользователя

Результаты поиска

Содержание Flex Fuel

Отзывы:

Похожие инструкции для Flex Fuel

Бренды по названию

Популярные бренды