Wood master Flex Fuel Скачать руководство пользователя страница 26

Страница: 26 / 76

Flex Fuel Owner’s Manual

March 2011

8.2 Menu Navigation

Scrolling Through the System Components

On the starting screen, turn the control knob to the right or left; the actual values and conditions of the

existing system components are displayed by this method. By pressing the control knob you will bring

up the settings menu of the system components. Pressing the ESC button will bring you back to the

starting screen. An example is shown below.

8: Display

FLEX FUEL

V 10.060 Tu, 12.09.10

Bulk materials
Boiler temperature:

Flue gas temperature:

Air factor:

Boiler is switched off!

81ºF

13:44

117ºF

7.40

BASIC BOILER SETTINGS

Set required boiler values

Select boiler operating mode

Boiler cleaning

Vacuum output/heat exchanger

Set clock/date

Service menu

Alarm protocol

Output test - heat cycle

Output test - boiler

Operating hour counter
Language selection & Unit

BASIC BOILER SETTINGS

Set required boiler values

Select boiler operating mode

Boiler cleaning

Vacuum output/heat exchanger

Set clock/date

Service menu

Alarm protocol

Output test - heat cycle

Output test - boiler

Operating hour counter
Language selection & Unit

BASIC BOILER SETTINGS

Set required boiler values

Select boiler operating mode

Boiler cleaning

Vacuum output/heat exchanger

Set clock/date

Service menu

Alarm protocol

Output test - heat cycle

Output test - boiler

Operating hour counter
Language selection & Unit

Set CLOCK/DATE

Date: 10.09.10
Time: 17:05

Set CLOCK/DATE

Date: 10.09.10
Time: 17:05

Set CLOCK/DATE

Date:

10.09.10

Time: 17:05

Set CLOCK/DATE

Date:

.09.10

Time: 17:05

Screen 1

Screen 2

Screen 3

Screen 7

Screen 8

Screen 4

Screen 5

Screen 6

• From the start screen (Screen 1) press the control knob to bring up screen 2.

• Press the control knob again and turn it clockwise to scroll down to “Set clock/date” and press the

control knob to select. (Screen 3)

• This will bring up the Set CLOCK/DATE screen. (Screen 4) Press the control knob to select “Date”. (Screen 5)

• By pressing the control knob again the cursor will move to the date values. (Screen 6)

• You may either turn the control knob to change the value and press on the control knob to set it or

press the ESC button to not change the value and return to the screen heading. (Screen 7)

• Press ESC again to return to the BASIC BOILER SETTINGS screen. (Screen 8)

• Press ESC one more time to return to the start screen. (Screen 1)

Содержание Flex Fuel













































































Результаты поиска

Содержание Flex Fuel

Отзывы:

Похожие инструкции для Flex Fuel

Бренды по названию

Популярные бренды

Wood master Flex Fuel, Руководство пользователя

Результаты поиска

Содержание Flex Fuel

Отзывы:

Похожие инструкции для Flex Fuel

Бренды по названию

Популярные бренды