Whirlpool Cassinetta Скачать руководство пользователя страница 19 | Manualshive

Страница: 19 / 78

background image

19

Vacation Mode:

This function deactivates the refrigeration
compartment if the user is going away for
sometime

Reset filter/alarm:

In the event of an alarm, the acoustic alarm
and indicator lights are activated. To disable
the acoustic signal, press Reset filter/alarm
button. If not manually deactivated by
pressing the button, the acoustic alarm
will switch off automatically after 10 minutes.

Child lock:

This function is used to completely lock the
control panel and the water and ice dispenser
Reset filter/alarm and Vacation mode buttons
for about 3 second or the child lock button
when available: one symbol (key) will
come on and an acoustic alarm will indicate
activation of the function. To deactivate the
function, carry out the same procedure until
the symbol goes off

ECO mode:

Activation of “Eco Mode”:
Press the ice & water button and the reset

alarm button at the same time for 2

seconds. After the 2 seconds the “Eco” icon

will turn ON and 13 seconds later the

display turns OFF. The buzzer sounds one
time.
Deactivation of the “Eco Mode”:
Press the ice & water button and reset alarm
button at the same time for 2 seconds.
After 2 seconds the “Eco” icon will turn OFF
and 13 seconds later the display remains
ON. The buzzer sounds one time.
Note: If there exist a power supply
interruption, the “Eco“ function is also
deactivated.

«
...
17
18
19
20
21
...
»

Содержание Cassinetta















































































Отзывы:

Нет отзывов

Похожие инструкции для Cassinetta

Бренд: Magic Chef Страницы: 6

Бренд: U-Line Страницы: 12

Бренд: U-Line Страницы: 24

Бренд: Heinner Страницы: 117

RISE JFFCF72DKL

Бренд: Jenn-Air Страницы: 3

Бренд: Daewoo Страницы: 12

Бренд: eta Страницы: 112

Avallon AWC243TSZLH

Бренд: Ferguson Enterprises Страницы: 21

IK 30 254 Series

Бренд: Gaggenau Страницы: 72

Бренд: ZANKER Страницы: 44

Monogram ZFSB23DRSS

Бренд: Monogram Страницы: 2

Бренд: U-Line Страницы: 15

Бренд: Parmco Страницы: 7

Бренд: Igloo Страницы: 28

Бренд: Omcan Страницы: 100

Бренд: Scandomestic Страницы: 53

Бренд: SNAIGE Страницы: 13

Бренд: Lloyd Страницы: 28

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды