Whirlpool Cassinetta Скачать руководство пользователя страница 27 | Manualshive

Страница: 27 / 78

background image

27

Icemaker E-module - Optical diagnostic

The service diagnostics mode only checks the functionality of the optics. To enter this mode,
turn E-module (Ice-Maker) OFF by means the User Interface Ice-Maker ON/OFF push-button,
then ON again; open the freezer door and look at the diagnostic GREEN LED hidden behind
E-module (Ice-Maker) service door.

Trouble shooting chart for optics diagnostic

TEST

RESULT

POSSIBLE CAUSE

CORRECTIVE

ACTION

Dirt on optics.

Clean dirt from optics.

Frost on optics lenses.

Clean frost from lenses.

2 LED pulses, repeated.

Failed optics.

Replace emitter and

receiver boards and

retest.

1 LED pulses, repeated.

E-module (Ice maker) is

in 5 minutes “harvest”

cycle.

To verify, look at the

blades, they should
turning to reach the

home position. If not,

replace E-module (Ice-

Maker).

Incorrect wiring at E-

module (Ice-Maker),

emitter or receiver

board.

Correct wiring and re-

test.

No LED pulses.

No power to E-module

(Ice-Maker).

Replace E-module (Ice-

Maker) and re-test.

Optics

Diagnostic

Mode (optics

test only)

LED solid ON

E-module (Ice-Maker)

powered with blades at

home position and

waiting for next harvest.

Everything is OK. No

corrective actions are

necessary.

WARNING

Electrical Shock Hazard

Voltage is present during these tests.

SbS IDI R600 ELECTRONIC E-module

«
...
25
26
27
28
29
...
»

Содержание Cassinetta















































































Отзывы:

Нет отзывов

Похожие инструкции для Cassinetta

Бренд: Zanotti Страницы: 86

Бренд: NEFF Страницы: 17

Echelon CO2075FF

Бренд: U-Line Страницы: 2

Бренд: U-Line Страницы: 2

Бренд: U-Line Страницы: 20

Echelon 2115RS00

Бренд: U-Line Страницы: 20

Бренд: U-Line Страницы: 2

Бренд: U-Line Страницы: 58

Combo CO2175DWR

Бренд: U-Line Страницы: 2

Бренд: U-Line Страницы: 35

Бренд: U-Line Страницы: 2

WINE CAPTAIN 2275DWRCOL

Бренд: U-Line Страницы: 17

Бренд: U-Line Страницы: 32

Бренд: V-ZUG Страницы: 36

Бренд: U-Line Страницы: 28

Бренд: Palsonic Страницы: 9

Бренд: Indesit Страницы: 12

Бренд: Avanti Страницы: 32

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды