Whirlpool Cassinetta Скачать руководство пользователя страница 29 | Manualshive

Страница: 29 / 78

background image

29

Icemaker E-module - Component diagnostic (forced harvest)

1.

Switch OFF the Ice-Maker using the User Board push-button.

2.

Remove the cap hidden behind the E-module (Ice-Maker) service door (to see picture

below). It is not more necessary slide out the Ice-Maker of the mounting rails.

3.

Switch ON the Ice-Maker using the User Board push-button.

4.

Open the freezer door and press by means a pen or small screwdriver the push-button

behind the cap removed. A harvest should start in a few seconds, i.e the ice cube rake is
turning.

5.

Wait until the blades reaches the home position then verify that the water valve

(BLACK one) is engaged for 7,5 seconds ± 1 second in order to fill up the Ice-Maker
mould with the water coming from the tap.

6.

Test passed.

Note:

The forced harvest switch (bimetal bypass) allows the service engineer to check

motor function, heater (feel the mould for heat during 5 seconds after power-up), and
valve fill when it returns to home.

As you can notice this can now all be done without removing the Ice-Maker from
Freezer compartment.

Diagnostic GREEN LED

Forced harvest switch
cover cap

«
...
27
28
29
30
31
...
»

Содержание Cassinetta















































































Отзывы:

Нет отзывов

Похожие инструкции для Cassinetta

Бренд: Daewoo Страницы: 12

Бренд: Daewoo Страницы: 11

Бренд: Samsung Страницы: 20

Бренд: Concept2 Страницы: 84

Бренд: Accucold Страницы: 12

Бренд: Inoksan Страницы: 42

Бренд: Indesit Страницы: 16

Бренд: Häfele Страницы: 48

Бренд: Hotpoint Страницы: 16

Combo CO2175DWR

Бренд: U-Line Страницы: 17

Бренд: Gastrodomus Страницы: 29

Бренд: Amica Страницы: 60

Бренд: NEFF Страницы: 27

Бренд: Veripart Страницы: 140

Бренд: U-Line Страницы: 25

Бренд: Frigidaire Страницы: 4

Бренд: Frigidaire Страницы: 4

Бренд: Frigidaire Страницы: 9

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды