Whirlpool Cassinetta Скачать руководство пользователя страница 30

Страница: 30 / 78

Trouble shooting chart for component diagnostic

TEST

RESULT

POSSIBLE CAUSE

CORRECTIVE ACTION

Ice Maker is not

powered.

Switch ON the Ice Maker by

means the User Board and retest.

Thermal fuse in Ice

Maker harness is open.

Replace ice maker harness and

retest.

Incorrect wiring at emitter

or receiver board.

Correct wiring and retest.

No LED pulses.

Problem with Ice Maker

See "Ice Maker Checks” below.

2 LED pulses.

Optics board defective.

Replace emitter and receiver

boards and retest.

LED on steady.

Ice Maker control circuit

is functioning normally.

None required.

Ice

Maker

Control

Circuit

1 LED pulses, repeated.

Ice-Maker in harvest

mode.

Wait till the blades reach rest

position.

Thermal fuse in Ice

Maker harness is open.

Replace ice maker harness.

No power applied to Ice

Maker module.

Wiring harness problem.

Check continuity in wiring

harness.

Ejector bar does not

move.

Motor has failed.

Replace ice maker E-module.

Water valve wiring

connection problem.

Check wiring to valve.

Customer’s water supply

is problem.

Check for proper water supply.

Frozen water fill tube.

Defrost the water fill tube and

check for seeping valve.

Ice

Maker

Checks

No water fill.

Water valve has failed.

Replace water valve.

Содержание Cassinetta















































































Результаты поиска

Содержание Cassinetta

Отзывы:

Похожие инструкции для Cassinetta

Бренды по названию

Популярные бренды

Whirlpool Cassinetta, Руководство по ремонту

Результаты поиска

Содержание Cassinetta

Отзывы:

Похожие инструкции для Cassinetta

Бренды по названию

Популярные бренды