Whirlpool Cassinetta Скачать руководство пользователя страница 13

Страница: 13 / 78

List of common questions from customer / end consumer

Old ITW 7 Segment dispenser – version

How works........ ?

Answer

Freezer- Fridge Temperature:

Freezer and Fridge compartment temperature
control: to change the internal temperature

press this button.

Water filter:

Water filter indicator: at the time of purchase

of the product and after replacement, the filter
symbol in green. The filter symbol can
become red according to product use and the
natural depletion of the filter charge.

The filter must be only be replaced when the
symbol on the display is red.

Alarm button:

Push the Alarm button for disable the

acoustic alarm.

Child lock:

This function is used to lock the water and

ice dispenser.

Содержание Cassinetta















































































Результаты поиска

Содержание Cassinetta

Отзывы:

Похожие инструкции для Cassinetta

Бренды по названию

Популярные бренды

Whirlpool Cassinetta, Руководство по ремонту

Результаты поиска

Содержание Cassinetta

Отзывы:

Похожие инструкции для Cassinetta

Бренды по названию

Популярные бренды