Whirlpool Cassinetta Скачать руководство пользователя страница 15

Страница: 15 / 78

List of common questions from customer / end consumer

LCD – version

How works........ ?

Answer

Freezer Temperature button:

Freezer compartment temperature control
button

Fridge Temperature button:

Fridge compartment temperature control
button

Menu button:

This button is used to select the various
optional functions. Each time the button is
pressed, a different option is highlighted.

OK button:

The OK button is used to confirm the
selected function and to deactivate the
acoustic signal

Ice On/Off:

Use the Ice On/Off button to switch the ice
maker on or off. When the ice maker is on,
the display show on icon light

Ice mode button:

Press this button to select the type of ice
desired: crushed or cubes

Light button:

Ice and water light can be switched On and
Off by pressing the Light button on the
control panel or pressing one of the two
dispenser levers; the light will switch off
automatically once the water or ice has been
dispensed.

Stand-by button:

This button needs to switch ON/OFF the
appliance without remove the power supply.
It must be pressed during 3 seconds.

Содержание Cassinetta















































































Результаты поиска

Содержание Cassinetta

Отзывы:

Похожие инструкции для Cassinetta

Бренды по названию

Популярные бренды

Whirlpool Cassinetta, Руководство по ремонту

Результаты поиска

Содержание Cassinetta

Отзывы:

Похожие инструкции для Cassinetta

Бренды по названию

Популярные бренды