Whirlpool Cassinetta Скачать руководство пользователя страница 39

Страница: 39 / 78

COMPONENTS DIAGNOSTIC MODE CHART

TEST

RESULT

POSSIBLE CAUSE

CORRECTIVE ACTION

Ice Maker is not
powered.

Checks poles relay output on the
Main Board.

Thermal fuse in Ice
Maker harness is open.

Replace ice maker harness.

No power applied to Ice
Maker module.

Wiring harness problem.

Check continuity in wiring
harness.

Ejector bar does not
move.

Motor has failed.

Replace ice maker module.

Thermostat jumper not
making contact.

Reposition jumper.

Heater is not on.

Heater has failed

Replace ice maker.

Thermostat jumper was
left installed past 11:00
position.

Remove jumper by 10:00 position
of ejector bar.

Water valve wiring
connection problem.

Check wiring to valve.

Customer’s water supply
is problem.

Check for proper water supply.

Frozen water fill tube.

Defrost the water fill tube and
check for seeping valve.

No water fill.

Water valve has failed.

Replace water valve.

Ice

Maker

Checks

Ejector bar does not stop
at “home” position.

Thermostat jumper not
removed.

Remove thermostat jumper.

Содержание Cassinetta















































































Результаты поиска

Содержание Cassinetta

Отзывы:

Похожие инструкции для Cassinetta

Бренды по названию

Популярные бренды

Whirlpool Cassinetta, Руководство по ремонту

Результаты поиска

Содержание Cassinetta

Отзывы:

Похожие инструкции для Cassinetta

Бренды по названию

Популярные бренды