manualshive.com logo in svg

Wacker Neuson DT08-D, Руководство оператора

Поделиться
Скачать
Wacker Neuson DT08-D Скачать руководство пользователя страница 81

BA DT08 SL EN – Edition 1.0  * dt08b530.fm

5-21

Maintenance

Battery

Danger!

Battery acid is highly caustic! 

Danger of burns!

Therefore when recharging and/or working near the battery:

☞

Always wear goggles and protective clothing with long sleeves

If acid is spilt:

☞

Thoroughly rinse all affected surfaces immediately with plenty of water

☞

Thoroughly wash any part of the body touched by the acid immediately with 
plenty of water and seek medical attention at once!

Especially when charging batteries, as well as during normal operation of 
batteries, an oxyhydrogen mixture is formed in the battery cells –

Danger of explosion!

☞

Avoid naked lights and sparks in the vicinity of the battery and do not 
smoke!

☞

Do not attempt to jump-start the machine if the battery is frozen or if the 
acid level is low. The battery can rupture or explode!

• Replace the battery immediately

☞

Always disconnect the negative terminal (–) from the battery before starting 
repair work on the electrical system!

Battery

A

 is located under the cover. The battery is “maintenance-free”. However have the 

battery checked at regular intervals to ensure that the electrolyte level is between the MIN 
and MAX marks.
Checking the battery requires it to be removed and must be carried out by an authorised 
workshop.
Always follow the specific battery safety instructions!

Notice!

Do not disconnect the battery while the engine is running!

Disconnecting the battery in an emergency

• Firmly pull cable 

C

 to disconnect the battery in an emergency.

Notice!

Firmly pull cable 

C

 in an emergency only since this damages the electric line and 

possibly the starter.

Fig. 86: Battery

-

+

A

Fig. 87: Battery

C

Содержание DT08-D







































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды