Wacker Neuson DT08-D Скачать руководство пользователя страница 65

Страница: 65 / 102

BA DT08 SL EN – Edition 1.0 * dt08b510.fm

5-5

Maintenance

Petrol specification

Use only high-grade fuels

For model DT08-P (petrol engine)

Diesel fuel specification

Use only high-grade fuels

For model DT08-D (diesel engine)

Cleaning the fuel filter (petrol engine)

Danger!

Petrol is extremely flammable, and explosive under certain circumstances.

Danger of accidents!

☞

No smoking in the work area, no naked flames or sparks.

☞

Once the filter cup is back in position, check for leaks and ensure that all
petrol spills have been wiped away before starting the engine.

☞

Set the fuel cock to OFF

☞

Unscrew filter cup

with a suitable tool

☞

Remove filter cup

and O-ring

, and wash with a nonflammable solvent.

☞

Allow filter cup

to dry thoroughly

☞

Screw filter cup

back on again with a suitable tool

☞

Set the fuel cock to ON and check for leaks

Grade

Octane
number

Use

• Regular DIN 51607

−

15 °C to 45 °C

Grade

Cetane
number

Use

• No. 2-D according to DIN

51 601

Min. 45

4 °C to 45 °C

• No. 1-D according to DIN

51601

For outside temperatures below 4 °C or for
operation above 1500 m altitude

Fig. 72: Filter cup DT08-P (petrol engine)

Содержание DT08-D







































































































Результаты поиска

Содержание DT08-D

Отзывы:

Бренды по названию

Популярные бренды

Wacker Neuson DT08-D, Руководство оператора

Результаты поиска

Содержание DT08-D

Отзывы:

Бренды по названию

Популярные бренды