Wacker Neuson DT08-D Скачать руководство пользователя страница 57

Страница: 57 / 102

BA DT08 SL EN – Edition 1.0 * dt08b340.fm

3-27

Operation

Dumping out the skip upwards (option)

Danger!

Careful when handling the high-tip skip –

Danger of accidents!

☞

Do not raise or dump out the skip when driving

☞

Do not raise or dump out the skip on slopes or in an inclined position

☞

Place the machine on level and horizontal ground

☞

Dump out skip

upwards

☞

Pull control lever

backwards

➥

Skip is raised

☞

Dump out skip

☞

Push control lever

forwards

➥

Skip dumps out

Emergency lowering of the skip

Danger!

Emergency lowering of the skip –

Danger of crushing and injury!

☞

Stay clear of the skip

Emergency lowering of the skip is only possible with the help of two persons.

☞

Pull lever

backwards

during emergency lowering and keep it in this position

• Once the skip is fully dumped out

☞

Push the skip downwards by hand beyond pivot point

and at the same time, pull

lever

backwards

☞

The skip is lowered by its own weight once it is beyond the pivot point.

Fig. 63: Dumping out the skip upwards (option)

Fig. 64: Emergency lowering of the skip

Содержание DT08-D







































































































Результаты поиска

Содержание DT08-D

Отзывы:

Бренды по названию

Популярные бренды

Wacker Neuson DT08-D, Руководство оператора

Результаты поиска

Содержание DT08-D

Отзывы:

Бренды по названию

Популярные бренды