manualshive.com logo in svg

Wacker Neuson DT08-D, Руководство оператора

Поделиться
Скачать
Wacker Neuson DT08-D Скачать руководство пользователя страница 53

BA DT08 SL EN – Edition 1.0  * dt08b340.fm

3-23

Operation

1.01.03

3.4

Working with the machine

General safety instructions

• Never drive up to the edge of a pit from outside – danger of cave-in!
• Do not drive under projecting earth. Stones or earth can fall onto the machine.
• When working on roofs or similar structures, check the resistance and the structure 

itself before starting work. The building can collapse, causing severe injury and 
damage to property.

• Do not place the machine directly under the workplace during demolition, otherwise 

demolished parts can fall onto the machine or the building can collapse, causing severe 
injury or damage.

• Operation of the machine by unauthorised staff is prohibited!
• The hydraulic system of the machine is still pressurised even when the engine is not 

running! Release the pressure in the sections of the system and hydraulic lines which 
are to be opened before starting setup or repair work, e.g. fitting/removing an 
attachment with hydraulic functions.

• Before dumping out the skip next to an excavation, secure the machine with suitable 

wheel chocks or other auxiliary means.

• Always watch the material as you dump out the skip: ensure that the material is 

dumped out evenly and does not remain stuck in the skip, otherwise the machine could 
tip over.

• Do not dump the load when working on sloping ground.
• No transporting of persons, animals etc. in the skip.
• When transporting material, actuating the skip and/or the loader unit (option) is not 

allowed!

• Always carry out precise and smooth control movements, do not carry out abrupt 

movements.

• Do not get off the machine when it is moving.
• Avoid dangerous work conditions on the work site, do not work in severe weather and 

ensure that no-one is at risk.

• Transporting persons is prohibited.

Working with the loader unit

The following section describes work operations with the machine equipped with the 
loader unit. The loader unit is mainly used for earth-moving applications, and for loosening, 
picking up and loading loose material.

Transporting with a full bucket

Caution!

No transport of material: the loader unit is designed for loading loose material 
only.

☞

Loading loose material is described below

☞

Only load material with the skip dumped in

Operation

Содержание DT08-D







































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды