Wacker Neuson DT08-D Скачать руководство пользователя страница 77

Страница: 77 / 102

BA DT08 SL EN – Edition 1.0 * dt08b530.fm

5-17

Maintenance

5.6 Tracks

Danger!

Careful when working with tracks –

Danger of accidents!

☞

Use suitable means to support and secure the machine

☞

In addition, ensure that the machine cannot overturn

Checking track tension

Check track tension as follows:

☞

Park the dumper on firm and level ground

☞

Raise the dumper with suitable means

☞

Tracks must be raised off the ground

☞

Stop the engine

☞

Use additional supports for the dumper and ensure that it cannot overturn

☞

Measure the clearance at the middle track roller

➥

The rubber track should not sag more than 15 mm when tight

Notice!

If possible, the distance from the rollers should be the same for both tracks.

Increasing track tension

Proceed as follows:

☞

Park the dumper on firm and level ground

☞

Raise the dumper with suitable means

☞

Tracks should be raised off the ground

☞

Stop the engine

☞

Use additional supports for the dumper and ensure that it cannot overturn

☞

Screw in set screw

with a suitable tool

➥

Ram

is extended

➥

The track is tightened

☞

Check track tension

➥

Repeat the procedure if the tracks are not tight enough

Notice!

Check track tension once a day since excessive or insufficient track tension can
damage the tracks and the components of the undercarriage.

Fig. 83: Checking track tension

15 mm

Fig. 84: Increasing track tension

Maintenance

Содержание DT08-D







































































































Результаты поиска

Содержание DT08-D

Отзывы:

Бренды по названию

Популярные бренды

Wacker Neuson DT08-D, Руководство оператора

Результаты поиска

Содержание DT08-D

Отзывы:

Бренды по названию

Популярные бренды