manualshive.com logo in svg

Wacker Neuson DT08-D, Руководство оператора

Поделиться
Скачать
Wacker Neuson DT08-D Скачать руководство пользователя страница 36

3-6

BA DT08 SL EN – Edition 1.0 * * dt08b330.fm

Operation

Before starting the engine

☞

Run through the “Start-up” checklist

General information on starting the petrol engine

Caution!

Never start the petrol engine without petrol!

☞

Always check the fuel tank contents before!

• The engine will not start unless the fuel cock is open
• Do not run the starter for more than 5 seconds if the engine does not start
• Wait about 10 seconds before trying again

Procedure

After you have completed the starting preparations:

☞

Open the engine cover

☞

Turn fuel cock 

A

 to the right

☞

Turn choke lever 

B

 to the left

Notice!

Do not use choke lever 

B

 if the engine is warm or at high air temperatures.

☞

Slightly move throttle 

6

 forwards

☞

Turn the engine switch to position 

E

 

Fig. 23: Fuel cock

A

B

Fig. 24: Throttle

6

Fig. 25: Engine switch

D

E

Operation

Содержание DT08-D







































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды