manualshive.com logo in svg

Wacker Neuson DT08-D, Руководство оператора

Поделиться
Скачать
Wacker Neuson DT08-D Скачать руководство пользователя страница 28

2-8

BA DT08 SL EN – Edition 1.0 * * dt08b210.fm

Safety instructions

• Have loads fastened and crane operators guided by experienced persons only!

The person guiding the operator must be within sight or sound of him

• Always use specially designed or otherwise safety-oriented ladders and working 

platforms to carry out overhead assembly work.
Never use machine parts or attachments/superstructures as a climbing aid!
Wear a safety harness when carrying out maintenance work at greater heights!
Keep all handles, steps, handrails, platforms, landings and ladders free from dirt, snow 
and ice! 

• Clean the machine, especially connections and threaded unions, of any traces of oil, 

fuel or preservatives before carrying out maintenance/repair work!
Do not use aggressive detergents!
Use lint-free cleaning rags! 

• Before cleaning the machine with water, steam jet (high-pressure cleaner) or deter-

gents, cover or tape up all openings which – for safety and functional reasons – must 
be protected against water, steam or detergent penetration. Special care must be taken 
with the electrical system.

• After cleaning, remove all covers and tapes applied for that purpose! 
• After cleaning, examine all fuel, lubricant and hydraulic oil lines for leaks, chafe marks 

and damage!
Rectify all defects without delay! 

• Always tighten any screw connections that have been loosened during maintenance 

and repair! 

• Any safety devices removed for set-up, maintenance or repair purposes must be 

refitted and checked immediately upon completion of the maintenance and repair work.

• Ensure that all consumables and replaced parts are disposed of safely and with 

minimum environmental impact! 

• Do not use the work equipment as lifting platforms for persons! 
• Before taking up work on machine parts dangerous for life and limb (bruising, cutting), 

always ensure safe blocking/support of these areas

• Carry out maintenance and repair work beneath a raised machine, attachments or 

additional equipment only if a safe and secure support has been provided for (the sole 
use of hydraulic rams, jacks etc. does not sufficiently secure raised machines or 
equipment/attachments)

• Avoid contact with hot parts, such as the engine block or the exhaust system during the 

operation of the machine and for some time afterwards – danger of burns! 

• Retainer pins can fly out or splinter when struck with force – danger of personal injury! 
• Do not use starting fuel! This especially applies to those cases in which a heater plug 

(intake-air preheating) is used at the same time – danger of explosions! 

• Apply special care when working on the fuel system – increased danger of fire! 

Содержание DT08-D







































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды