Wacker Neuson DT08-D Скачать руководство пользователя страница 73 | Manualshive

Страница: 73 / 102

Wacker Neuson DT08-D Скачать руководство пользователя страница 73

BA DT08 SL EN – Edition 1.0 * dt08b520.fm

5-13

Maintenance

5.5

Hydraulic system

Specific safety instructions

• Release the pressure in all lines carrying hydraulic oil prior to any maintenance and

repair work. To do this:
• Lower all hydraulically controlled attachments to the ground
• Move all control levers of the hydraulic control valves several times

• Hydraulic oil escaping under high pressure can penetrate the skin and cause serious

injuries. Always consult a doctor immediately even if the wound seems insignificant –
otherwise serious infections could set in!

• If the hydraulic oil in the sight glass is cloudy, this indicates that water or air has

penetrated the hydraulic system. This can cause damage to the hydraulic system!

☞

Contact your Wacker Neuson dealer immediately

• Oil or fuel flowing out of high pressure lines can cause fire or malfunctions, and severe

injuries or damage to property. Interrupt work immediately if slack nuts or damaged
hoses and lines are detected.

☞

Contact your Wacker Neuson dealer immediately

• Replace a line if one of the following problems is detected:

☞

Damaged or leaky hydraulic seals.

☞

Worn or torn shell, or bare reinforcement

☞

Expanded shells in several positions.

☞

Entangled or crushed movable parts.

☞

Foreign bodies jammed or stuck in protective layers.

Caution!

Dirty hydraulic oil, lack of oil or wrong hydraulic oil –

Danger of severe damage to the hydraulic system!

☞

Take care to avoid dirt when working!

☞

Always fill in hydraulic oil using the filling screen!

☞

Only use authorised oils of the same type

– see chapter 5.9

Fluids and lubricants

☞

Always fill up hydraulic oil before the level gets too low

hydraulic oil

☞

If the hydraulic system is filled with biodegradable oil, then use only biode-
gradable oil of the same type for filling up – observe the sticker on the
hydraulic oil tank!

☞

Contact customer service if the hydraulic system filter is contaminated with
metal chippings. Otherwise, follow-on damage can result!

Environment!

Collect drained hydraulic oil and biodegradable oil in a suitable container!
Dispose of drained oil and used filters by an ecologically safe method.
Always contact the relevant authorities or commercial establishments in charge of oil dis-
posal before disposing of biodegradable oil.

«
...
71
72
73
74
75
...
»

Содержание DT08-D







































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды