Wacker Neuson DT08-D Скачать руководство пользователя страница 16

Страница: 16 / 102

1-8

BA DT08 SL EN – Edition 1.0 * * dt08b110.fm

Introduction

1.9

Type labels and component numbers

Serial number

The serial number is located on the type label.
The type label is located at the rear right of the control stand.
Type label information
Machine designation:

COMPACT DUMPER

Model:

---------------

Model year:

---------------

CEE no.:

---------------

Output:

---------------

Serial no.:

---------------

Max. payload:

---------------

GWR:

---------------

Operating weight:

---------------

Front GAWR:

---------------

Transport weight:

---------------

Rear GAWR:

---------------

Version:

---------------

Other information

– see chapter 6

Specifications

on page 6-33

Engine number

The type label (arrow) is located next to the oil check plug.

The type label (arrow) is located below the tank (engine).

Fig. 3:

Position of the type label

COMPACT DUMPER

Fig. 4:

Engine number (petrol engine)

Fig. 5:

Diesel engine number

Содержание DT08-D







































































































Результаты поиска

Содержание DT08-D

Отзывы:

Бренды по названию

Популярные бренды

Wacker Neuson DT08-D, Руководство оператора

Результаты поиска

Содержание DT08-D

Отзывы:

Бренды по названию

Популярные бренды