Volvo Penta 120S Скачать руководство пользователя страница 51

Страница: 51 / 88

Repair - MS2 reverse gear and upper gear housing, sailboat drive

116. Reverse gear MS2

Put a new O-ring on the cover.

Make sure that the oil drain is correctly aligned. Screw
the cover down onto the housing.

117. Reverse gear MS2

Put on a new O-ring, put the tested thickness of
shims on the output bearing housing, and then fix it to
the housing with screws.

Turn the shaft slightly, to allow the gear teeth to
mesh. Install the gear bracket with two of the screws.

118. Drive, 120S, 120S-B, -C, -D, -E

Put on a new O-ring and install the rear cover and
gear bracket on the upper gear.

Install the sea water valve. Use sealant, Volvo Penta
part no. 1141570 on the threads.

119.

Put a new O-ring and the tested thickness of

shims on the input bearing housing.

NOTE!

The bearing housing can only be installed in

one position, because of the hole pattern. Screw the
bearing housing down onto the housing.

Содержание 120S

























































































Результаты поиска

Содержание 120S

Отзывы:

Похожие инструкции для 120S

Бренды по названию

Популярные бренды

Volvo Penta 120S, Руководство по ремонту

Результаты поиска

Содержание 120S

Отзывы:

Похожие инструкции для 120S

Бренды по названию

Популярные бренды