Volvo Penta 120S Скачать руководство пользователя страница 60

Страница: 60 / 88

Repair of MS2V reverse gear, angle gear

28.

Screw two screws into the tubular shaft and fix it

in a vise. Align the tubular nut with the un-threaded
section towards the crown wheel and install it with tool
no.

884860.

Tightening torque:

140 Nm (103.26 lbf ft)

884860

29.

Press the outer roller bearing on. Use sleeve

884835

30.

Put shims with a total thickness of 0.70 mm be-

tween the cover and the housing.

Install the tubular shaft in the housing and fix it with
two diagonally opposed screws.

Tightening torque:

25 Nm (18.44 lbf ft)

Check the pre-load with a spring balance,

9985494

and a piece of string wound round the tubular shaft.

Pre-load:

10-16 N (2.25-3.60 lbf)

Too low pre-load:

Increase the shim thickness under

the upper cover.

Too high pre-load:

Reduce the shim thickness under

the upper cover.

Check the pre-load again and continue until the cor-
rect pre-load has been obtained.

9985494

2.25-3.60 lbf

Содержание 120S

























































































Результаты поиска

Содержание 120S

Отзывы:

Похожие инструкции для 120S

Бренды по названию

Популярные бренды

Volvo Penta 120S, Руководство по ремонту

Результаты поиска

Содержание 120S

Отзывы:

Похожие инструкции для 120S

Бренды по названию

Популярные бренды