Volvo Penta 120S Скачать руководство пользователя страница 76 | Manualshive

Страница: 76 / 88

background image

74

Repair - lower gear housing, sailboat drive

Model 120S
Installation, lower gear
housing–adapter housing

Preferably use the shims which were installed previ-
ously, if only new bearings have been installed. Shim
thickness can also be measured as in the points be-
low.

58.

Check that there is no end float in the vertical

shaft. Then install spacer ring (

1

).

59.

Use a depth micrometer

9985472

to measure the

distance (

A

) from the division plane down to the spac-

er ring (

1

).

1

56.

On the other hand, if the marking pattern is dis-

placed in relation to the figure above, the thickness of
the shims underneath the front bearing race must be
increased and the thickness of the shims behind the
bearing race in the rear bearing housing must be re-
duced to the same extent.

NOTE!

In this case, the propeller shaft will be dis-

placed backwards (away from the pinion), which
means that the flank clearance will be too large. This
can not be changed in any other way than by remov-
ing the vertical shaft, pressing off the roller bearings
and changing the ferrule.

Install a new ferrule. Then re-install the bearings and
put the shaft back in the gear housing. Turn round to
establish the new flank clearance and check the
marking pattern. Please refer to items 50-51.

57.

When the correct flank clearance has been ob-

tained, disassemble the tool and propeller shaft, and
wash off all marker dye from the crown wheel and pin-
ion.

Re-install the propeller shaft and rear bearing housing.
Please refer to item 47. Then install the upper, outer
bearing race. Use tool no.

884757

.

884757

1

A

9985472

«
...
74
75
76
77
78
...
»

Содержание 120S

























































































Отзывы:

Нет отзывов

Похожие инструкции для 120S

Бренд: Jabiru Страницы: 103

Бренд: Briggs & Stratton Страницы: 102

Бренд: PCM Страницы: 83

Бренд: Beckhoff Страницы: 31

Бренд: Deutz Страницы: 257

Бренд: O.S. engine Страницы: 15

Бренд: Applied Motion Products Страницы: 2

Бренд: IMS Страницы: 6

Бренд: Yamakoyo Страницы: 41

Бренд: cemp Страницы: 18

Бренд: CW Products Страницы: 4

Бренд: Wilesco Страницы: 4

Бренд: Wilesco Страницы: 2

Бренд: Wilesco Страницы: 4

Бренд: Wilesco Страницы: 4

Бренд: Wilesco Страницы: 4

Бренд: Wilesco Страницы: 4

Бренд: Detroit Diesel Страницы: 174

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды