Volvo Penta 120S Скачать руководство пользователя страница 77

Страница: 77 / 88

Repair - lower gear housing, sailboat drive

60.

Measure the thickness of gasket (

) with mi-

crometer

9999701

61.

Measure the height of flange (

) on the adapter

housing.

Example:

When distance (

) is measured, we obtain a dis-

tance of 5.70 mm in this case.

Gasket (

) thickness is measured as 0.30 mm.

Flange height (

) is measured as 3.85 mm.

A + B – C = shim thickness

5.70 + 0.30 – 3.85 = 2.15

Shim thickness = 2.15 mm

9999701

62.

Install the calculated thickness of shims and gas-

ket on the division plane of the lower gear housing.

NOTE!

The text on the gasket must face upwards.

The hole pattern in the gasket only fits one way round.

63.

Install the adapter housing with rubber sleeve on

the lower gearing housing. Apply MoS

based grease,

Volvo Penta part no. 1161029-2 to the socket cap
screws. Put washers on the six socket cap screws
and use a torque wrench to tighten them.

Tightening torque:

30 Nm (22.13 lbf ft)

NOTE!

Torque the screws diagonally, then re-check

their tightening.

Install the cooling water tap on the port side. Apply
sealant, Volvo Penta part no. 1141570-0 on the
threads.

NOTE!

Check that the adapter flange has entered the

gear housing and presses the shims down, so that
there is no end float in the vertical shaft. Also check
the flank clearance.

Содержание 120S

























































































Результаты поиска

Содержание 120S

Отзывы:

Похожие инструкции для 120S

Бренды по названию

Популярные бренды

Volvo Penta 120S, Руководство по ремонту

Результаты поиска

Содержание 120S

Отзывы:

Похожие инструкции для 120S

Бренды по названию

Популярные бренды