Volvo Penta 120S Скачать руководство пользователя страница 80

Страница: 80 / 88

Repair - lower gear housing, sailboat drive

Oil and install a new O-ring (1) in the cutout in the
adapter plate.

74.

Fit the gear housings together. Apply MoS2 based

grease, Volvo Penta part no. 1161029-2 to the socket
cap screws. Install the screws, 10 pcs. The two long
screws should be located by the rear edge.

Put washers under the screw heads and distribute the
screws with holes in the screw heads so that there are
two on each side.

Tightening torque:

30 Nm (22.13 lbf ft)

73.

Install the adapter plate on the upper gear hous-

ing. Apply MoS2 based grease, Volvo Penta part no.
1161029-2 to the three socket cap screws. Put wash-
ers on the socket cap screws and use a torque
wrench to tighten them. Torque the screws alternately.

Tightening torque:

30 Nm (22.13 lbf ft)

Install the slipping clutch (

72.

Oil and install a new O-ring on the adapter section

neck.

Reverse installed drive (180°)

Содержание 120S

























































































Результаты поиска

Содержание 120S

Отзывы:

Похожие инструкции для 120S

Бренды по названию

Популярные бренды

Volvo Penta 120S, Руководство по ремонту

Результаты поиска

Содержание 120S

Отзывы:

Похожие инструкции для 120S

Бренды по названию

Популярные бренды