Volvo Penta 120S Скачать руководство пользователя страница 73

Страница: 73 / 88

Repair - lower gear housing, sailboat drive

46.

Lock the pinion nut with tool

3858852

. Press the

shaft down and make sure that the pinion nut engages
in the tool. Fix the tool to the rear bearing housing, us-
ing socket cap screws.

Install tool

884264

884830

on the vertical shaft.

Tighten the pinion nut.

Wrench size:

17 mm

Tightening torque:

110 ± 10 Nm (81.13 ± 7.38 lbf ft)

47.

Install the bearing housing on the propeller shaft.

NOTE!

Turn the shaft carefully, to avoid damaging the

sealing lips on the seal rings.

Apply sealant, Volvo Penta part no. 1161231-4, to the
mating face between the bearing housing and the
drive.

Then install the propeller shaft and bearing housing on
the gear housing.

Apply thread locking fluid, Volvo Penta part no.
1161231-4, to the screws.

Tightening torque:

30 Nm (22.13 lbf ft).

48.

Install the upper nut on the vertical shaft.

NOTE!

The chamfered side of the nut must face

downwards.

884753

49.

Then screw tool

884753

to the division plane, so

that the “teeth” engage on the nut. Fix the tool, with
the lower gear housing, in a vice.

NOTE!

First tighten the nut by hand, so that the tool

lies flush against the division plane.

884264
884830

3858852

Содержание 120S

























































































Результаты поиска

Содержание 120S

Отзывы:

Похожие инструкции для 120S

Бренды по названию

Популярные бренды

Volvo Penta 120S, Руководство по ремонту

Результаты поиска

Содержание 120S

Отзывы:

Похожие инструкции для 120S

Бренды по названию

Популярные бренды