Volvo Penta 120S Скачать руководство пользователя страница 27

Страница: 27 / 88

Repair - MS2 reverse gear and upper gear housing, sailboat drive

22.

Pull up the sliding sleeve with a turning motion.

23. Reverse gear MS2

Press the outer bearing race out, using the vertical
shaft. Keep hold of the vertical shaft, to prevent it
from falling and being damaged. Save any shims be-
neath the bearing race.

NOTE

! On the sailboat drive, the shaft is loose since

there are no bearings.

24.

Put the vertical shaft in a press and press the

large washer with tool no.

884725

, to release the re-

tention ring halves. Remove the halves.

9991801

884733

884725

25.

Remove the lock washer (1), the large domed

washer (2), the three smaller domed washers (3), any
spacer washers (4) and the needle roller bearing (5).

26.

Press the gear wheel out. Use tool no.

884733

combination with standard shaft

9991801

Содержание 120S

























































































Результаты поиска

Содержание 120S

Отзывы:

Похожие инструкции для 120S

Бренды по названию

Популярные бренды

Volvo Penta 120S, Руководство по ремонту

Результаты поиска

Содержание 120S

Отзывы:

Похожие инструкции для 120S

Бренды по названию

Популярные бренды