Volvo Penta 120S Скачать руководство пользователя страница 75 | Manualshive

Страница: 75 / 88

background image

73

Repair - lower gear housing, sailboat drive

Marking pattern

52.

When the correct gear flank clearance has been

obtained, remove tool

884753

from the lower gear.

Then turn the tool so that the “teeth” (

A

) face out-

wards. Fix the tool with two screws to the lower gear
housing.

Press the vertical shaft in with tool no.

884766

which

is screwed to the other tool. Leave tool

884264

or

884830

in place.

Then disassemble the propeller shaft and apply mark-
er dye to the gear wheels.

53.

Install the propeller shaft again and turn it round in

both directions.

Brake the propeller shaft strongly.

NOTE!

Press the vertical shaft in with tool no.

884766

at the same time as it is turned round.

54.

Disassemble the propeller shaft and check that

the marking pattern on the gear teeth corresponds
with the marking pattern in the illustration above or the
figures in items 55 and 56.

55.

If the marking pattern is displaced in relation to

the figure above, the thickness of the shims under-
neath the front bearing race must be reduced and the
thickness of the shims behind the bearing race in the
rear bearing housing must be increased to the same
extent. It is important that the preload is not changed.

NOTE!

In this case, the propeller shaft is displaced

forwards (towards the pinion), which reduces flank
clearance. For this reason, it is necessary to install
tool no.

884753

and tighten the upper nut a bit more

until correct flank clearance has been obtained.

Please refer to items 50 and 51. Then check the con-
tact patch again, as in items 52-54.

884766

884753

884766

A

884264
884830

«
...
73
74
75
76
77
...
»

Содержание 120S

























































































Отзывы:

Нет отзывов

Похожие инструкции для 120S

Бренд: SEW-Eurodrive Страницы: 88

Бренд: Stuart Turner Страницы: 20

Бренд: Yamaha Страницы: 30

Бренд: Toyama Страницы: 44

Бренд: TIS Страницы: 12

Gasoline V6 90 Degree

Бренд: GMC Страницы: 94

Бренд: Lister Petter Страницы: 60

Бренд: O.S. engine Страницы: 2

Бренд: O.S. engine Страницы: 4

Бренд: O.S. engine Страницы: 2

Бренд: O.S. engine Страницы: 4

Бренд: Motion Страницы: 124

Бренд: TAARKS Страницы: 9

Бренд: Briggs & Stratton Страницы: 20

Бренд: Ford Страницы: 46

Бренд: Vetus Страницы: 134

Бренд: DAF Страницы: 40

Бренд: TRAXX Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды