Volvo Penta 120S Скачать руководство пользователя страница 46

Страница: 46 / 88

Repair - MS2 reverse gear and upper gear housing, sailboat drive

Checking the marking pattern
and gear flank clearance

98.

Try installing an 0.40 mm shim in the input bearing

housing.

Install the bearing housing on the housing.

99.

Put the vertical shaft, with needle roller bearing, in

the housing. The lower needle roller bearing is retained
by a rubber band or O-ring.

The illustration shows the location of the bearing (1)
and O-ring (2).

Gear housing

96.

Install the lower roller bearing in the housing.

NOTE!

Align the narrow ring by the arrow upwards.

The ring has a sharp edge which would cut into the
casting if it were installed crookedly. For this reason,
be careful to ensure that the bearing is correctly
aligned in the bearing seat.

Use tool no.

884731

and shaft

9991801

97.

Install the circlip, using circlip pliers.

NOTE!

The chamfered side must face upwards. Make

sure that the circlip is securely seated in the groove.

Содержание 120S

























































































Результаты поиска

Содержание 120S

Отзывы:

Похожие инструкции для 120S

Бренды по названию

Популярные бренды

Volvo Penta 120S, Руководство по ремонту

Результаты поиска

Содержание 120S

Отзывы:

Похожие инструкции для 120S

Бренды по названию

Популярные бренды