Volvo Penta 120S Скачать руководство пользователя страница 65

Страница: 65 / 88

Repair - lower gear housing, sailboat drive

11.

Install tool no.

884743

in the lower gear housing.

Use a 5/16" x 20 mm (3/4") screw. Alternatively, one
of the drive fixing screws can be used together with a
5 mm thick washer.

Take out the loose needles (25 pcs) if the needle roller
bearing needs to be changed.

Tighten the screw with the steel ball so that it presses
the vertical shaft up. Wrench size

24 mm

. Then dis-

assemble the tool.

12.

Disassemble the outer bearing race from the upper

part of the gear housing, using tool no.

884761

combination with tool no.

884721

13.

Remove the bearing race with expander

884750

and shaft

884143

The expander is inserted from underneath, and the
shaft from above.

884743

884750

884143

884761

884721

884761

10.

Disassemble the bearing race with tool no.

884761

NOTE

! Note the number of shims between the bearing

race and the gear.

Содержание 120S

























































































Результаты поиска

Содержание 120S

Отзывы:

Похожие инструкции для 120S

Бренды по названию

Популярные бренды

Volvo Penta 120S, Руководство по ремонту

Результаты поиска

Содержание 120S

Отзывы:

Похожие инструкции для 120S

Бренды по названию

Популярные бренды