Volvo Penta 120S Скачать руководство пользователя страница 53

Страница: 53 / 88

Undo the four socket cap screws which retain the

pinion in the housing, and disassemble the pinion.
Save the shims between the gear housing and the pin-
ion.

Repair of MS2V reverse gear, angle gear

This section only refers to repair of the angle gear and
its sub-components. Please refer to the MS2 informa-
tion for general information about the reverse gear.

Clean the outside of the reverse gear. Remove the

drain plug (1) and drain the oil.

Undo the 4 nuts, the 2 socket cap screws and re-

move the angle gear from the reverse gear.

Tubular shaft,
disassembly

Undo the six screws which hold the tubular shaft in

the housing, and drive out the tubular shaft with a lead
hammer etc. Save the shims between the cover and
the gear housing.

Содержание 120S

























































































Результаты поиска

Содержание 120S

Отзывы:

Похожие инструкции для 120S

Бренды по названию

Популярные бренды

Volvo Penta 120S, Руководство по ремонту

Результаты поиска

Содержание 120S

Отзывы:

Похожие инструкции для 120S

Бренды по названию

Популярные бренды