Volvo Penta 120S Скачать руководство пользователя страница 31

Страница: 31 / 88

Repair - MS2 reverse gear and upper gear housing, sailboat drive

884724

884729

884757

9985494

2.25-4.05 lbf

39.

Place the drive shaft in the bearing housing and

press the small roller bearing on, using tool no.

884729

NOTE

! Do not press the bearing until it bottoms. A

certain amount of clearance must be left. When the
nut is torqued to the correct value, the bearing hous-
ing is pre-loaded and the clearance disappears.

40.

Screw a new nut on. Turn the chamfer inwards.

NOTE

! The nut must always be changed.

Use tool no.

884724

. Start off with low torque. Please

refer to the following chapter.

41.

Test the pre-load with a spring balance. Fix the

gear wheel or shaft in a vise with soft jaw pads. Wind
a string round the bearing housing, and pull with spring
balance no.

9985494

Pre-load:

10-18 N (2.25-4.05 lbf)

Not enough pre-load:

Increase the torque on the nut.

Too much pre-load:

Reduce the torque on the nut.

42.

Oil and install the seal ring carefully, to avoid

damage to the seal lip. Use tool no.

884757

to drive

the ring in.

Содержание 120S

























































































Результаты поиска

Содержание 120S

Отзывы:

Похожие инструкции для 120S

Бренды по названию

Популярные бренды

Volvo Penta 120S, Руководство по ремонту

Результаты поиска

Содержание 120S

Отзывы:

Похожие инструкции для 120S

Бренды по названию

Популярные бренды