Viessmann Vitotronic 200 KW2 Скачать руководство пользователя страница 46 | Manualshive

Страница: 46 / 120

background image

46

Function description

Boiler temperature control

Brief description

The boiler water temperature is
regulated by starting and shutting
down the burner.
In the delivered condition, the
switching differential is ±2 K, relative
to the current set value.
The set boiler water temperature
depends on the boiler and the
heating/control versions installed. It
is calculated from the set flow
temperatures of the heating circuit
without mixer, the mixer circuit and
the set DHW temperature.
When the DHW cylinder is heated
up, a set boiler water temperature is

applied, which lies 20 K above the
set DHW cylinder value (adjustable
via coding address 60). The boiler
water temperature is limited by
control thermostat TR.
The actual boiler water temperature
is required for the control of the
heating circuits and the DHW
cylinder.

Coding addresses which influence
the boiler temperature control

02, 04, 06, 13.
For a description, see the coding
overview.

Functions

The boiler water temperature is
recorded by three sensors
separately:

H

High limit safety cut−out STB
(liquid expansion)

H

Control thermostat TR
(liquid expansion)

H

Boiler temperature sensor KTS
(change in resistance PT 500)

Upper control limits

H

High limit safety cut−out
STB110/100/95

º

C

H

Control thermostat TR75/87/95

º

C

H

Electronic maximum limit
Setting range: 20 to 130

º

C, change

via coding address 06.
This limit is only effective within
the control range (not for DHW
cylinder heating).

Lower control limits

H

Ultra low temperature boiler:
At an outside temperature of 1

º

C,

the boiler water temperature will
be regulated to at least 15/22

º

C

(frost protection).

H

Low temperature boiler:
Controls the boiler water
temperature in standard mode and
frost protection to 35/42

º

C. For

changes, see coding address A3
(variable frost limit).

5862700GB

«
...
44
45
46
47
48
...
»

Содержание Vitotronic 200 KW2

























































































































Отзывы:

Нет отзывов

Похожие инструкции для Vitotronic 200 KW2

Бренд: U.S. Range Страницы: 12

Бренд: U.S. Boiler Company Страницы: 2

GRAND PELLET 100

Бренд: Metal-Fach Страницы: 60

Бренд: Laars Страницы: 36

Бренд: Lochinvar Страницы: 72

Бренд: Daikin Страницы: 64

Бренд: ideal commercial Страницы: 28

Бренд: Sime Страницы: 80

Бренд: Raypak Страницы: 6

RIVA PLUS M90D.24S

Бренд: Biasi Страницы: 48

RIVA OV M110.18SM/OV

Бренд: Biasi Страницы: 40

Бренд: Biasi Страницы: 16

RIVA ADVANCE HE M110B.24SM/C

Бренд: Biasi Страницы: 52

Бренд: Biasi Страницы: 88

Бренд: Baxi Страницы: 48

Brava One 25 BF

Бренд: Sime Страницы: 136

Maior Eolo 24 4E

Бренд: Immergas Страницы: 30

Бренд: Immergas Страницы: 142

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды