Viessmann VITODENS 200-W B2HA 112 Скачать руководство пользователя

Страница: 21 / 104

Vitodens 200-W B2HA 112, 150 Service

5683 710 - 09

Start-up and Service

Check Coaxial Venting System for Leaks

(circular air gap measurement)

Viessmann strongly recommends that the heating

contractor perform a simplified leak test during boiler

start-up. For this purpose it is sufficient to measure

the CO

concentration of the combustion air in the

coaxial gap of the air intake pipe. The vent pipe is

considered sufficiently leak-proof if a CO

concentration

in the combustion air no higher than 0.2% or an O

concentration no lower than 20.6% is measured.

If higher CO

values or lower O

values are measured,

check venting system thoroughly.

Note:

The vent pipe adaptor comes with two

measurement ports, one for combustion air-intake

measurement and one for flue gas measurement.

Remove Burner Assembly

1. Switch the main power supply and the ON/OFF

switch

“

” on the boiler control to OFF.

Note:

Slide the black control cover outwards to

access the ON/OFF switch.

2. Shut off the gas valve.
3. Fold down control unit

and remove cover

4. Pull the cables from the fan motor

, gas valve

ionization electrode

and ignition module

5. Release gas supply pipe fitting

Note:

there is a gasket between the gas valve and

the

fitting.

6. Loosen the six Torx (T-30) screws

and remove

burner.
7. Check burner gasket

for damage. Generally

replace the burner gasket every 2 years.

CAUTION

To avoid damage to the burner, do not lay burner on its

cylindrical burner tube or touch the burner tube mesh.

Failure to heed this caution may cause damage to the

burner tube, which may lead to improper operation.

Содержание VITODENS 200-W B2HA 112









































































































Результаты поиска

Содержание VITODENS 200-W B2HA 112

Отзывы:

Похожие инструкции для VITODENS 200-W B2HA 112

Бренды по названию

Популярные бренды

Viessmann VITODENS 200-W B2HA 112, Инструкция по эксплуатации

Результаты поиска

Содержание VITODENS 200-W B2HA 112

Отзывы:

Похожие инструкции для VITODENS 200-W B2HA 112

Бренды по названию

Популярные бренды