Viessmann VITODENS 200-W B2HA 112 страница 55 Скачать руководство пользователя

Страница: 55 / 104

Vitodens 200-W B2HA 112, 150 Service

5683 710 - 09

Coding 2

Boiler

Select “Boiler”

Coding
Coding in the factory setting

Possible change

01:1

Single boiler system

01:2

Multi boiler system with Vitotronic

300-K.

04:1

Minimum burner pause subject

to the boiler load (specified by

boiler coding card)

04:0

Minimum burner pause set

permanently (specified by boiler

coding card).

06:...

Maximum limit of the boiler

water temperature, specified

in °C by the boiler coding card

06:20

06:127

Maximum limit of the boiler water

temperature within the ranges

specified by the boiler.

07:1

Boiler number in multi boiler

systems

07:2

07:8

Boiler number 2 to 8 in multi-

boiler systems.

08:...

Maximum burner heating output

in kW in the case of a multi

boiler system

08:0

08:199

Maximum burner heating output

adjustable from 0 to 199 kW

(limited by boiler specific

parameters) in steps of 1 kW.

0D:0

DO NOT ADJUST

0E:0

DO NOT ADJUST

13:1

DO NOT ADJUST

14:1

DO NOT ADJUST

15:1

DO NOT ADJUST

21:0

No service interval (hours run)

selected

21:1

21:100

Number of hours run before the

burner should be serviced is

adjustable from 100 to 10,000 h

One adjusting step

≙

100 h.

23:0

No time interval for burner

service

23:1

23:24

Interval adjustable from 1 to 24

months.

24:0

No “Service” display

24:1

“Service” display (the address is

automatically set and must be

manually reset after a service has

been carried out).

28:0

No burner interval ignition

28:1

28:24

Interval adjustable from 1 hour

to 24 hours. The burner is force

started once every 30 seconds

(only when operating with LPG).

2E:0

DO NOT ADJUST

2F:0

Venting program/fill program

disabled

2F:1

Venting program enabled.

2F:2

Fill program enabled.

30:0

Coding address should be set

to 30:0, if not adjust to 30:0

30:3

When changing from a single

boiler to a multiboiler operation,

the coding address may

automatically reset to 30:3. To

prevent continuous boiler pump

operation, adjust the coding

address for each boiler to 30:0.

31:...

NOT USED

Set speed in % of the internal

circulation pump when operated

as boiler circuit pump, specified

by the boiler coding card

31:0

31:100

Set speed adjustable from

0 to 100%.

38:0

Status burner control unit:

Operational (no fault)

38:

≠

Status burner control unit: Fault.

Содержание VITODENS 200-W B2HA 112









































































































Результаты поиска

Содержание VITODENS 200-W B2HA 112

Отзывы:

Похожие инструкции для VITODENS 200-W B2HA 112

Бренды по названию

Популярные бренды

Viessmann VITODENS 200-W B2HA 112, Инструкция по эксплуатации

Результаты поиска

Содержание VITODENS 200-W B2HA 112

Отзывы:

Похожие инструкции для VITODENS 200-W B2HA 112

Бренды по названию

Популярные бренды