Viessmann VITODENS 200-W B2HA 112 Скачать руководство пользователя

Страница: 17 / 104

Vitodens 200-W B2HA 112, 150 Service

5683 710 - 09

1. To measure static and/or running pressure remove

boiler enclosure panel as indicated page 12 in these

instructions.
2. Close gas shutoff valve (field supplied).
3. Loosen screw at inlet gas pressure port

on the

gas combination valve, do not remove completely.

Connect

manometer.

4. Open the gas shutoff valve.
5. Measure static pressure. Values must be:

14 “w.c. maximum for NG

14 “w.c. maximum for LPG

6. Enter measured value into Maintenance Record on

page 96 in this manual.

7. Start up boiler, using the ON/OFF switch “

” on the

boiler

control.

Note:

Slide the black control cover outwards to

access the ON/OFF switch.

8. Measure the running pressure; value must be:

Note:

Use suitable measuring instruments calibrated

with a minimum resolution of 0.04 “w.c. for

measuring the running pressure.

9. Enter gas type into Maintenance Record on page 96

in this manual.

10. Switch off the ON/OFF switch “

” on the boiler

control, close the gas shut-off valve, remove the

manometer and re-tighten the screw at inlet gas

pressure

port

Start-up and Service

Measure Static Pressure and Running Pressure

A CO measurement (see page 25) must be taken before

and after working on gas appliances to eliminate risks to

health and to guarantee the satisfactory condition of the

system.

The burner is automatically ignited and starts operation

after a safety time has elapsed. During initial start-up,

the unit may indicate a fault because of air in the gas

supply pipe (especially for liquid propane gas). After

approx. 5 seconds, press the ”R” button to reset the

burner. The ignition procedure is repeated. This boiler

employs a direct spark ignition system.

WARNING

Ensure that there is no open flame in the room.

WARNING

Never purge a gas line into a combustion chamber.

Never use matches, candles, flame, or other sources of

ignition for purpose of checking leakage. Use a soap and

water solution to check for leakage. A failure to follow

this warning could result in fire, explosion, personal

injury or death.

IMPORTANT

Running supply pressure with

Corrective action

LPG

under 4 ”w.c. under 4 ”w.c.

Do not start the boiler.

Notify your gas supply

utility or LPG supplier.

4 to 14 “w.c. 10 to 14 “w.c. Start up boiler.
over 14 “w.c. over 14 “w.c.

Do not attempt

adjustment. Call local

gas utility to decrease

pressure or install up

stream gas pressure

regulator. Boiler valve

must not be exposed to

pressure over 14 ”w.c.

Содержание VITODENS 200-W B2HA 112









































































































Результаты поиска

Содержание VITODENS 200-W B2HA 112

Отзывы:

Похожие инструкции для VITODENS 200-W B2HA 112

Бренды по названию

Популярные бренды

Viessmann VITODENS 200-W B2HA 112, Инструкция по эксплуатации

Результаты поиска

Содержание VITODENS 200-W B2HA 112

Отзывы:

Похожие инструкции для VITODENS 200-W B2HA 112

Бренды по названию

Популярные бренды