Viessmann VITODENS 200-W B2HA 112 Скачать руководство пользователя страница 56

Страница: 56 / 104

Vitodens 200-W B2HA 112, 150 Service

5683 710 - 09

Coding 2

DHW

Select “DHW”

Coding
Coding in the factory setting

Possible change

56:0

Set DHW temperature

adjustable from 50 to 140° F

(10 to 60° C)

56:1

Set DHW temperature adjustable

from 50 to over 140° F (10 to

over 60° C)

Note:

Maximum value subject to

boiler coding card. Observe

the maximum permissible

DHW temperature.

58:0

Without auxiliary function for

DHW heating

58:10

58:60

Input of a second set DHW

temperature, adjustable from 50

to 140°F (10 to 60°C) (observe

coding addresses “56” and “63”).

59:0

DHW tank heating:

Starting point -2.5 K

Stopping point +2.5 K

59:1

59:10

Starting point adjustable from

1 to 10 K below the set value.

5b:0

DHW tank directly connected

to the boiler

5B:1

DHW tank connected downstream

of the low loss header.

5E:0

Circulation pump for DHW tank

heating stays in control mode

at signal “External blocking”

5E:1

Circulation pump for DHW

tank heating stops at signal

“External blocking”.

5E:2

Circulation pump for DHW

tank heating starts at signal

“External blocking”.

5F:0

Circulation pump for DHW tank

heating stays in control mode

at signal “External demand”

5F:1

Circulation pump for DHW

tank heating stops at signal

“External demand”.

5F:2

Circulation pump for DHW

tank heating starts at signal

“External demand”.

60:20

During DHW heating, the boiler

water temperature is maximum

20 K higher than the set DHW

temperature

60:5

60:25

The differential between the boiler

water temperature and the set

DHW temperature is adjustable

from 5 to 25 K.

62:2

Circulation pump with 2 minutes

run-on time after DHW tank

heating

62:0

Circulation pump without run-on.

62:1

62:15

Run-on time adjustable from 1 to

15 minutes.

Содержание VITODENS 200-W B2HA 112









































































































Результаты поиска

Содержание VITODENS 200-W B2HA 112

Отзывы:

Бренды по названию

Популярные бренды

Viessmann VITODENS 200-W B2HA 112, Инструкция по эксплуатации

Результаты поиска

Содержание VITODENS 200-W B2HA 112

Отзывы:

Бренды по названию

Популярные бренды