Viessmann VITODENS 200-W B2HA 112 Скачать руководство пользователя

Страница: 29 / 104

Vitodens 200-W B2HA 112, 150 Service

5683 710 - 09

Start-up and Shutdown

Outdoor Reset Programming Unit

Starting the heating system
1. Check the heating system pressure at the pressure

gauge. The heating system pressure is too low if

the indicator points to the area below 15 psi.

In this case, top up with water or notify your local

heating

contractor.

2. For room air dependent operation:

Check that the ventilation apertures of the installation

room are open and unrestricted.

Note:

With room air dependent operation, the

combustion air is drawn from the boiler room.

3. For Vitodens:

Open the gas shut-off valve.

Note:

Ask your heating contractor to explain the

positioning and handling of these components.

4. Switch ON the power supply, e.g. at a separate

power switch or fuse.

5. Turn the ON/OFF switch “

“ ON. After a short time,

the standard menu is displayed and the green ON

indicator illuminates. Your heating system and, if

installed, your remote controls are now ready for

operation.

Note:

Slide the black control cover outwards to

access the ON/OFF switch.

Legend

Fault indicator (red)

ON indicator (green)

Reset button

ON/OFF switch

Pressure gauge

Menu

There are two control levels available, the “Standard menu” and the “Extended menu”.

Standard menu
Note:

If your heating system has 2 or 3 heating circuits:

You can select the heating circuit “

HC1

”, “

HC2

”

“

HC3

” to be displayed in the standard menu.

If your heating system only has 1 heating circuit:

No heating circuit name “

...” is shown in the

header.
In the standard menu, you can adjust and scan the most

frequently used settings for the heating circuit shown in

the header:

Press the following keys to set room temperature:

for the required value

to confirm

Heating programs:

Standby mode with frost protection monitoring

Only DHW

Heating and DHW

Press the following keys:

for the required heating program

to confirm

Note:

2 minutes after any setting has been made, the

display automatically reverts to the standard menu.

Legend

Header (shows the heating program for displayed

heating

circuit

Current outside temperature

Set room temperature

Heating circuit

which is

selected

for

operation

in the standard menu

Содержание VITODENS 200-W B2HA 112









































































































Результаты поиска

Содержание VITODENS 200-W B2HA 112

Отзывы:

Похожие инструкции для VITODENS 200-W B2HA 112

Бренды по названию

Популярные бренды

Viessmann VITODENS 200-W B2HA 112, Инструкция по эксплуатации

Результаты поиска

Содержание VITODENS 200-W B2HA 112

Отзывы:

Похожие инструкции для VITODENS 200-W B2HA 112

Бренды по названию

Популярные бренды