Viessmann VITODENS 200-W B2HA 112 Скачать руководство пользователя

Страница: 15 / 104

Vitodens 200-W B2HA 112, 150 Service

5683 710 - 09

Start-up and Service

Check Power Supply Connection

Note:

The outer conductor “L “ and the neutral conductor

“N” must not be interchanged.

See wiring diagram on page 88 in section entitled

“Additional Information”.

IMPORTANT

In Canada all electrical wiring is to be done in accordance

with the latest edition of CSA C22.1 Part 1 and/or local

codes. In the U.S. use the National Electrical Code ANSI/

NFPA 70. The heating contractor must also comply with

both the Standard for Controls and Safety Devices for

Automatically Fired Boilers, ANSI, ASME CSD-1.

Select Gas Type

Note:

the Vitodens 200-W, B2HA boiler is factory set to

operate with natural gas . See following subsection

for conversion instructions to liquid propane gas.

1. Ensure that the fuel type listed on the boiler rating

plate is the correct type for the installation being

attempted.

2. Record fuel type in Maintenance Record on page 96.

The Vitodens 200-W boiler is for use with gases whose

characteristics fall within the following ranges.

Do not use any other types of gas.

Natural gas

Liquid propane gas

Heating value (gross)

Btu/ft

970 to 1100

2466 to 2542

Specific gravity

0.57 to 0.70

1.522 to 1.574

Ultimate carbon dioxide (CO

)

11.7 to 12.2

13.73 to 13.82

An external accessories connection box is attached to

the Vitodens 200-W, B2HA boiler, which requires a

120VAC power supply from a wall receptacle (15A fuse

protected).

Refer to the Installation Instructions shipped with the

boiler.

Voltage range

The voltage at connector 40 of the boiler control must be

120V (see wiring diagram).

Neutral conductor

The electrical power supply must have a neutral

conductor.

Designating Heating Circuits

In the delivered condition, the heating circuits are

designated "Heating circuit 1", "Heating circuit 2" and

"Heating circuit 3" (if installed).

If the system user prefers, the heating circuits can be

designated differently to suit the specific system.

To enter names for heating circuits:

Refer to the Operating Instructions

Содержание VITODENS 200-W B2HA 112









































































































Результаты поиска

Содержание VITODENS 200-W B2HA 112

Отзывы:

Похожие инструкции для VITODENS 200-W B2HA 112

Бренды по названию

Популярные бренды

Viessmann VITODENS 200-W B2HA 112, Инструкция по эксплуатации

Результаты поиска

Содержание VITODENS 200-W B2HA 112

Отзывы:

Похожие инструкции для VITODENS 200-W B2HA 112

Бренды по названию

Популярные бренды