Viessmann VITODENS 200-W B2HA 112 Скачать руководство пользователя страница 78

Страница: 78 / 104

Vitodens 200-W B2HA 112, 150 Service

5683 710 - 09

Fault Codes

(continued)

Troubleshooting

Control mode: Boiler/burner fully operational (fault code must be verified and reset).

Burner in fault mode: Boiler control requires manual reset before burner can resume operation.

Burner blocked: If fault cause is corrected, burner resumes operation.

Detailed fault code coding address 38:xx (if available).

Fault code

on display

Detailed fault

code

System behavior

Cause

Corrective action

132

Burner in a fault mode

At burner start, flame

signal is missing or too

weak

Check gas supply (gas pressure

and gas regulator). Check gas

train. Check ionization electrode

and connecting cable.

Check ignition:

- Connecting leads to ignition

module and ignition electrode.

- Ignition electrode gap and

contamination (see page 23).

Check condensate drain.

Press reset button

138

Burner in a fault mode

Flame is lost immediately

after it has built (during

the safety time)

Check gas supply (gas pressure

and gas regulator). Check flue

gas/ventilation air system for

flue gas recirculation. Check

ionization electrode (replace

if required):

- Distance to burner gauze

assembly (see page 23).

- Contamination of electrode

Press reset button

Burner blocked

Internal fault

Replace the control unit.

135

Burner in a fault mode

Maximum flue gas

temperature exceeded

230ºF (110ºC) limit.

Check heating system fill level.

Bleed air from system. Check

circulation pump. Check boiler

water temperature sensor and

cable. Press reset button

after

vent system has cooled down.

129

Burner in fault mode

Fixed high limit switch

open (activated)

Check heating system fill

level. Check the circulation

pump. Bleed air from the

system. Check fixed high limit

switch and connecting cables.

Press reset button

139

Burner in fault mode

Flame signal already

present at burner start

Check the ionization electrode

and connecting cable.

Press reset button

148

Burner in fault mode

Gas valve closes too

late

Check the gas valve.

Check both control wiring/

connections.

Press reset button

151

152

Burner in fault mode

Fan speed too low

during burner start

Check the fan, the fan cables

and power supply. Check the

fan control.

Press reset button

Содержание VITODENS 200-W B2HA 112









































































































Результаты поиска

Содержание VITODENS 200-W B2HA 112

Отзывы:

Бренды по названию

Популярные бренды

Viessmann VITODENS 200-W B2HA 112, Инструкция по эксплуатации

Результаты поиска

Содержание VITODENS 200-W B2HA 112

Отзывы:

Бренды по названию

Популярные бренды