Videx IP videokit IPVK/6296 Series, Руководство по установке

Страница: 34 / 76

66550062-EN - V6.0 - 31/10/21
- 34 -
IPVK/6296 Series IP videokit
IPVK/6296 Series - Installation handbook
SETTING UP AN OUTDOOR PANEL 4533 - FUNCTIONAL DOOR PANEL
In the device list window ( Fig. 17 ), click on the button “Edit Properties” of one “OUTDOOR PANEL” model 4533.
If you are unsure which door panel is which, you can enable the flag “ACCEPT CONNECTION FROM DEVICES” (under the menu option
Settings->Preferences Fig. 12 on page 33 ) then press any button on the door panel to open the settings for that door panel.
The “ OUTDOOR PANEL SETTINGS ” window ( Fig. 18 ) shows the following device information:
• The Device Model
• The firmware version
• The hardware version
Then there is a section of editable fields*:
• The Device IP
• The Subnet Mask
• The Gateway IP
• The DNS 1
• The DNS 2
• The Device ID
• The Device Description
*If you are not sure, contact your system administrator to set the correct IP Address, subnet mask and Gateway.
It is recommended to set a descriptive “ DEVICE DESCRIPTION ” that identifies the area where the device is installed i.e. “Main En-
trance”, “Back Entrance” etc.
Under the “ GENERAL ” tab ( Fig. 18 ) you can set:
• The
Video Quality
For every kind of connection you can select among 5 levels - Note that a higher quality requires a higher band-
width so for direct connection to monitor you can select the maximum quality, for a connection to a client in the LAN you can
select a medium quality while it could be suggested to select a low quality for a client connected through wan;
• The Levels for
» The Reassurance Tone (3 levels) that is the reassurance tone emitted during a call that confirms the call in progress;
» The Microphone Gain (3 levels);
» The Loudspeaker Gain (3 levels) the loudspeaker has also the option to operate on the speaker unit POT;
• The
Noise attenuation
: check the box to activate the noise attenuation feature. When the outside environment is particularly loud,
it may be useful to enable this feature.
• The
External Camera Connection
. When the external camera is connected, it is required to set the default video signal which will
be shown during the call (Either the internal camera or the external camera). For both, built in and external camera, it is possible
to set a name that will be shown when switching video signal.
• The
Voice Annuciations
that, if enabled, allows to select between the “DOOR” and “GATE” messages for “Relay 1” and “Relay 2”.
The “ APT. ” tab ( Fig. 19 ) allows configuration of each call button to call one or more devices (the speaker unit module can include
up to 2 internal buttons and can be connected up to 40 external buttons):
• The “ Choose Button: ” list box will select the button you are assigning intercoms to (2 built in buttons / up to 40 external buttons).
• The “ Add Intercom To Button ” assigns the intercom selected through the “ Available Intercoms: ” list box to the selected call button.
One or more intercoms (Up to a maximum of 16) can be assigned to each button. Any intercom can be assigned to one or more but-
tons. If 2 or more intercoms are assigned to one button, the “ Cascade Mode ” can be enabled: in standard mode it allows cascading
call among all intercoms assigned to the button, the call is diverted to the next device after the “ Cascade Ringing time ” set (both the
Videx APP and the SIP ID will continue to ring at the same time for all the call duration), see next pages for a detailed description of the
advanced “ Cascade Mode: ” ().
» While programming the call buttons, if you don’t know the button number of the button that you are programming, you can
click on “ Identify Button ”, the software then waits for a button to be pressed. Once the button is pressed it is automatically
selected, if nothing happens when you press the push button, please, take care, you are probably editing properties of another
door panel or the module of the external button is not properly connected or set.
» To remove a videophone from the list of assigned devices click on the “ X ” button.
» In the field “ Call SIP ID: ” enter the SIP ID to call when the button is pressed. If the door panel is set to work with a third party SIP
server and you need this button to call a SIP device then this field will need to be filled. When the button will be pressed, will
be called all the intercoms assigned to the button plus the SIP ID set for that button.
The “ USERS SETTINGS “ tab ( Fig. 20 ) allows users to be stored in the door panel memory. The users are used in combination with
access codes and proximity keys for access control purposes. To any user can be linked one or more access code and one or more
proximity key so, by disabling the user are automatically disabled the relevant access codes and proximity keys.
Under this tab it is possible to set as user all the residents but it is possible to set as user also the periodic visitors like the postman
or the gardener.
• The “ USERS TABLE ” section allows big changes to be made on the users table and/or to edit, enable & delete a single user through
the relevant section.
» To automatically fill the user table from apartments list press the “autofill from apartments” button.
VX IP Wizard
Wizard configuration software for VIDEX IP System