background image

54  

••••

  Reference

XX002 Rev 799 Surveyor99 Dome System

Twisted-Pair Cable

CAUTION:  Careful selection of the proper cable is essential to obtain the best performance from this

equipment. Vicon assumes no responsibility for poor performance when cables other than
those recommended are installed.

Materials

Use a pure copper stranded conductor with or without a tin plating to obtain a low DC resistance. Do not use cable with
either a steel or an aluminum stranded conductor because these do not transfer signals effectively for long distances.
The preferred insulation and cable jacket is Polyvinyl chloride (PVC). It has better electrical characteristics than
polyethylene and resists flames, sunlight and most solvents, but is more vulnerable to moisture.

Cable Types

The most commonly used cable types are dual individually-shielded, twisted pair in a single jacket. This configuration is
the most convenient for RS-422/ RS485 applications. Single twisted pair is also a suitable cable.

Choose a Belden cable type by referring to the characteristics and maximum distances listed below. The maximum
distance for the most reliable digital control refers to the distance between the CPU/Keypad and the Camera Dome
Assembly. The characteristics of the cables in Table 5 should be used as a guideline when cables other than Belden are
used. Materials and construction must follow the guidelines above.

¹

Datalene is a Registered Trademark of Belden.

Table 5

Recommended Individually-Shielded, Twisted-Pair Cable Types

1.0-inch Pipe Designation

The standard “1.0-inch pipe” referred to in this manual has actual dimensions of:

Outside diameter: 1.315 inches (33.4 mm).
Inside diameter: 1.049 inches (26.6 mm).
Wall thickness: 0.133 inches (3.38 mm) minimum (ANSI “standard” grade thickness).

CABLE 

TYPE

WIRE SIZE 

(AWG)

INSULATION 

MATERIAL

JACKET 

MATERIAL

DISTANCE ft (m) 

max.

NUMBER OF 

TWISTED PAIRS

Belden 9406

22

PVC

PVC

5000 (1500)

2

Belden 9402

20

PVC

PVC

5000 (1500)

2

Belden 8723

22

Polypropylene

PVC

8000 (2400)

2

Belden 8162

24

Datalene¹

PVC

15000 (4600)

2

Belden 9729

24

Datalene¹

PVC

15000 (4600)

2

Belden 9182

22

Datalene¹

PVC

25000 (7600)

1

Содержание Surveyor 99






































































Отзывы: