VESPA 946 E4 EMEA 2021 Скачать руководство пользователя страница 124

Страница: 124 / 283

COIL

Function

Allows generation of the electrical discharge on

the spark plug, with an increase of voltage.

Pin-out:

1. Activation by control unit (control unit side PIN

2. Relay powered (PIN 87 relay side)

ELECTRICAL ERRORS

.V. Coil P0351 - shorted to positive / open circuit or short-circuit to negative.

Error cause

Short-circuit to positive: excessive voltage at PIN 1 of the control unit connector.

Open circuit or short-circuit to negative: interruption of the circuit or null voltage at PIN 1 of the control

unit connector.

Troubleshooting

Short-circuit to positive:

- Disconnect the coil connector, turn the key to ON and activate the component through the diagnostic

tool.

- Verify the presence of voltage on the coil connector PIN 1: if present, restore the cabling, otherwise

replace the coil.

Open circuit:

- Carry out the check procedure of the coil and control unit connectors.

- Verify continuity of the wiring harness between the coil and control unit: Coil PIN 1 - control unit PIN

1. If there is no continuity, restore the wiring harness.

- Verify, with the key turned ON, the presence of voltage on the coil connector PIN 2:. If no voltage is

read, verify the continuity of the cabling between coil and injection relay (No. 35 on the electrical circuit

diagram): Coil PIN 2 - relay PIN 87.

- If the above tests provided a positive result, the coil should be replaced.

Short-circuit to negative:

- Disconnect the control unit connector and the coil connector.

- Verify the coil connector PIN 1 ground insulation (or control unit connector PIN 1). Repair the wiring

harness if necessary.

Electrical system

Vespa 946 E4-E5 EMEA-USA-ASIA (2021-)

ELE SYS - 124

Содержание 946 E4 EMEA 2021




























































































































































































































































































Результаты поиска

Содержание 946 E4 EMEA 2021

Отзывы:

Похожие инструкции для 946 E4 EMEA 2021

Бренды по названию

Популярные бренды

VESPA 946 E4 EMEA 2021, Руководство пользователя

Результаты поиска

Содержание 946 E4 EMEA 2021

Отзывы:

Похожие инструкции для 946 E4 EMEA 2021

Бренды по названию

Популярные бренды