VESPA 946 E4 EMEA 2021 Скачать руководство пользователя страница 86 | Manualshive

Страница: 86 / 283

background image

B

= Speedometer

C

= Multifunction indicator

D

= ASR Icon

E

= High-beam warning light

F

= MIL warning light - Injection system failure warning light

G

= Immobilizer warning LED

H

= ABS warning light

I

= Low engine oil pressure warning light

L

= Turn indicator warning light

M

= Miniature «VESPA 946»

By turning the ignition key to the «

ON

» position all the digital display functions will light up for a few

seconds.

MULTIFUNCTION INDICATOR «C»

Acting on the MODE button this indicator displays the following functions in sequence:

- Clock (CLOCK)

- Total odometer (ODO)

- Partial odometer (TRIP)

For this indicator «

C

» and for the speed indicator «

B

» the unit of measurement can be changed (from

Km to Miles and from Kph to mph) with the following procedure:

- move the key to «

OFF

»;

- press the MODE button to the left;

- Holding in the MODE button, turn the key to the «

ON

» position;

- after about 2 seconds release the MODE button.

WARNING

TO SWITCH FROM km/h TO mph, THE MULTIFUNCTION INDICATOR "C" MUST BE SET TO TO-
TAL ODOMETER (ODO).

N.B.

THE FOLLOWING ARE DEFINED WHEN NAVIGATING THE DISPLAY:
- «BRIEF PRESS»: A PRESS OF THE INDICATED BUTTON, FOR A PERIOD OF LESS THAN TWO
SECONDS;
- «PROLONGED PRESS»: A PRESS OF THE INDICATED BUTTON, FOR A PERIOD OF MORE
THAN TWO SECONDS.

N.B.

THE VEHICLE IS EQUIPPED WITH A DEVICE ABLE TO
PRESERVE THE FUNCTIONALITY OF THE LIGHT ASSEM-
BLY IN CASE OF OVERHEATING.
THIS SYSTEM CONSISTS OF A SOFTWARE INTEGRATED
IN THE ENGINE ECU THAT RECEIVES SIGNALS FROM
THE DASHBOARD AND ADJUSTS THE LIGHT POWER
WHEN THE HEADLAMP'S TEMPERATURE IS TOO HIGH.
THIS MAY HAPPEN WHEN A PIECE OF CLOTHING OR A
FABRIC IS PLACED ON THE HEADLAMP OR ON THE HAN-
DLEBAR FOR A FEW MINUTES WHILE THE ENGINE IS
STATIONARY AND RUNNING AT IDLE.
WHEN THE FIRST TEMPERATURE THRESHOLD IS
REACHED, THE DISPLAY SHOWS AN "Alert" - "Light" AL-
TERNATING CYCLIC MESSAGE.

Electrical system

Vespa 946 E4-E5 EMEA-USA-ASIA (2021-)

ELE SYS - 86

«
...
84
85
86
87
88
...
»

Содержание 946 E4 EMEA 2021




























































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 946 E4 EMEA 2021

Бренд: X-TREME Страницы: 39

Бренд: Nipponia Страницы: 44

Бренд: Denver Страницы: 22

Бренд: Pride Страницы: 41

Бренд: F-Wheel Страницы: 8

Бренд: habitat et jardin Страницы: 18

Бренд: Viro Rides Страницы: 2

Бренд: Segway Страницы: 31

Бренд: Segway Robotics Страницы: 89

Бренд: CRUSSIS Страницы: 2

Бренд: Dynacraft Страницы: 27

Бренд: Trikke Страницы: 40

Shoprider Paris GK9

Бренд: Roma Medical Страницы: 20

Бренд: Benelli Страницы: 15

Navigator 100cc

Бренд: SMC Networks Страницы: 24

Бренд: DAELIM Страницы: 47

Бренд: kikkaride Страницы: 29

Бренд: kikkaride Страницы: 52

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды