manualshive.com logo in svg

VESPA 946 E4 EMEA 2021, Руководство пользователя


Поделиться
Скачать
background image

Fuses

The electrical system is protected by fuses located

under the central cover. To access them operate

as described in the «Battery» paragraph.

FUSES

Specification

Desc./Quantity

Fuse no. 1

Capacity:

 20 A

Protected circuits:

 vehicle general

Fuse no. 2

Capacity:

 10 A

Protected circuits:

 battery-powered injection solenoid, injec-

tion control unit and immobilizer LED, digital display.

Fuse no. 3

Capacity:

 20 A

Protected circuits:

 battery-powered, ABS control unit.

Fuse no. 4

Capacity:

 7.5 A

Protected circuits:

 battery-powered PMP pre-installation (ac-

cessory) and antitheft pre-installation.

Fuse no. 6

Capacity:

 7.5 A

Protected circuits:

 key powered, fuel level indicator, license

plate light, instrument illumination, turn indicator control, ABS

warning light, horn, rear daylight running lights, front daylight

running lights.

Fuse no. 7

Capacity:

 5A

Protected circuits:

 key powered, immobilizer antenna, tip

over sensor, starter circuit, stop button, stop light, ABS control

unit and engine control unit.

Fuse no. 8

Capacity:

 7.5 A

Protected circuits:

 key powered, USB socket pre-installation

(accessory), turn indicator control device, antitheft pre-instal-

lation.

Fuse no. 9

Capacity:

 5A

Protected circuits:

 key powered, high beam and headlight

warning light.

CAUTION

IN ORDER TO AVOID DAMAGING THE ELECTRICAL SYSTEM, NEVER DISCONNECT THE WIR-
ING WHILE THE ENGINE IS RUNNING. DO NOT TIP THE VEHICLE TOO MUCH IN ORDER TO
AVOID DANGEROUS LEAKAGE OF THE BATTERY ELECTROLYTE.

CAUTION

MODIFICATIONS OR REPAIRS TO THE ELECTRICAL SYSTEM, PERFORMED INCORRECTLY OR
WITHOUT STRICT ATTENTION TO THE TECHNICAL SPECIFICATIONS OF THE SYSTEM CAN
CAUSE MALFUNCTIONING AND RISK OF FIRE.

Vespa 946 E4-E5 EMEA-USA-ASIA (2021-)

Electrical system

ELE SYS - 99

Содержание 946 E4 EMEA 2021




























































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 946 E4 EMEA 2021

Rascal Vista Owner'S Manual preview
Vista
Бренд: Rascal Страницы: 28
C.T.M. HS-539 Manual preview
HS-539
Бренд: C.T.M. Страницы: 23
E-Glide D 150 Manual preview
D 150
Бренд: E-Glide Страницы: 9
Blaupunkt e mobility Clara Owner'S Manual preview
e mobility Clara
Бренд: Blaupunkt Страницы: 154
Yedoo NUMBERS FOUR User Manual preview
NUMBERS FOUR
Бренд: Yedoo Страницы: 21
Hudora Kiddyscooter Series Instructions On Assembly And Use preview
Kiddyscooter Series
Бренд: Hudora Страницы: 4
KMART JUNIOR NEO Instructions preview
JUNIOR NEO
Бренд: KMART Страницы: 3
Exclusive Brands Smart Glider Manual preview
Smart Glider
Бренд: Exclusive Brands Страницы: 16
Hover-1 DSA-EGE Operation Manual preview
DSA-EGE
Бренд: Hover-1 Страницы: 27
Planet Mobility GB-106 P3 Cruiser Owner'S Manual preview
GB-106 P3 Cruiser
Бренд: Planet Mobility Страницы: 39
Baotian Classic Service And Repair Manual preview
Classic
Бренд: Baotian Страницы: 100
Lemeego X E-Bike 2021 Manual preview
X E-Bike 2021
Бренд: Lemeego Страницы: 2
Benelli Hornet Operation & Maintenance Manual preview
Hornet
Бренд: Benelli Страницы: 15
Hudora Stuntboy Series Quick Start Manual preview
Stuntboy Series
Бренд: Hudora Страницы: 8
8Tev B12 Instruction Manual preview
B12
Бренд: 8Tev Страницы: 10
Schildkröt ROAD CATCHER RUNABOUT User Manual preview
ROAD CATCHER RUNABOUT
Бренд: Schildkröt Страницы: 35
Schildkröt 510101 User Manual preview
510101
Бренд: Schildkröt Страницы: 35
TNT 503359B Instructions preview
503359B
Бренд: TNT Страницы: 2

Бренды по названию

Популярные бренды

Загрузить еще бренды