manualshive.com logo in svg

VESPA 946 E4 EMEA 2021, Руководство пользователя


Поделиться
Скачать
background image

•

BUTTON «1» (with the engine run-

ning): activation / deactivation.

•

ICON «2»: operating indication icon.

Flashing mode:

- Off with the vehicle in gear:: the system is work-

ing, but is not active (normal condition).

- Flashing quickly with moving vehicle: The system

is functioning correctly and is active (poor grip con-

ditions, engine power limiting in effect); ride with

extreme care, as the grip limit has been exceeded;

restore the vehicle safety conditions by gently re-

ducing the throttle opening.

- Lit with moving vehicle: the system is disabled

and will not intervene in case of loss of grip.

•

If the deactivation was voluntary (by

pressing the appropriate button «1» for

1 second with the engine running) it is

recommended to reactivate the system

as soon as possible.

•

If the system was NOT deactivated vol-

untarily, this indicates an ASR system

fault.

To ensure maximum safety of the vehicle it is ad-

visable to keep the system active. Deactivation

may be necessary only in case of starting with very

low grip surfaces (mud, snow) on which the oper-

ation of the ASR could actually prevent the move-

ment of the vehicle.

N.B.

AT VEHICLE START-UP THE ASR ICON FLASHES AT THE
SAME FREQUENCY AS THE ABS WARNING LIGHT, INDI-
CATING A DIAGNOSTIC PHASE OF THE SYSTEM. IF NO
ERRORS ARE FOUND, THE ASR ICON AND THE ABS IN-
DICATOR LIGHT SWITCH OFF AT THE SAME TIME ONCE
THE VEHICLE SPEED EXCEEDS 5 Km/h (3 mph).
IF NO FLASHING OCCURS WHEN THE ENGINE IS STAR-
TED, THE SYSTEM MAY NOT BE WORKING.

WARNING

Braking system

Vespa 946 E4-E5 EMEA-USA-ASIA (2021-)

BRAK SYS - 236

Содержание 946 E4 EMEA 2021




























































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 946 E4 EMEA 2021

Youin SC7000 User Manual preview
SC7000
Бренд: Youin Страницы: 80
ECLYPSE Astra Bike Manual preview
Astra
Бренд: ECLYPSE Страницы: 15
babytiger SPIDO User Manual preview
SPIDO
Бренд: babytiger Страницы: 28
VOK electric cargo bike 2.0 User Manual preview
electric cargo bike 2.0
Бренд: VOK Страницы: 24
Roketa Moto Fino MF125QT-7 Manual preview
Moto Fino MF125QT-7
Бренд: Roketa Страницы: 30
PLAYTIVE 271532 Instructions For Use Manual preview
271532
Бренд: PLAYTIVE Страницы: 20
Motus Pro 8.5 lite Original User Manual preview
Pro 8.5 lite
Бренд: Motus Страницы: 20
HOMCOM 371-043 Assembly & Instruction Manual preview
371-043
Бренд: HOMCOM Страницы: 9
Huffy Tilt N Turn Owner'S Manual preview
Tilt N Turn
Бренд: Huffy Страницы: 20
Huffy In-Line Owner'S Manual preview
In-Line
Бренд: Huffy Страницы: 20
Planet Mobility Easy Travel Elite ET1E Owner'S Manual preview
Easy Travel Elite ET1E
Бренд: Planet Mobility Страницы: 24
Malaguti F10 Service Manual preview
F10
Бренд: Malaguti Страницы: 44
Golden Buzzaround XL GB117 Owner'S Manual preview
Buzzaround XL GB117
Бренд: Golden Страницы: 44
X-TREME METRO EXPRESS Owner'S Manual preview
METRO EXPRESS
Бренд: X-TREME Страницы: 15
X-TREME Baja 48V Owner'S Manual preview
Baja 48V
Бренд: X-TREME Страницы: 39
Group Vertical Self-Balancing Scooter User Manual preview
Self-Balancing Scooter
Бренд: Group Vertical Страницы: 21
X-TREME XM-5000Li Operation And Maintenance Instructions preview
XM-5000Li
Бренд: X-TREME Страницы: 21
X-TREME XMB-400 Owner'S Manual preview
XMB-400
Бренд: X-TREME Страницы: 34

Бренды по названию

Популярные бренды

Загрузить еще бренды