manualshive.com logo in svg

VESPA 946 E4 EMEA 2021, Руководство пользователя


Поделиться
Скачать
background image

the grip conditions, contributing significantly to the

maintenance of stability the vehicle.

WARNING

THE ASR SYSTEM IS BASED ON THE RECOGNITION OF
SPEED DIFFERENCES BETWEEN FRONT AND REAR
WHEEL. FOR THE SYSTEM TO PERFORM CORRECTLY IN
ALL CONDITIONS, THE PROCEDURE MUST BE PER-
FORMED EACH TIME A TYRE IS REPLACED EVEN IF ON-
LY ONE OF THE TYRES IS REPLACED.
FOR THE CALIBRATION OF THE ASR SYSTEM PERFORM
THE PROCEDURE BELOW.

For version EURO 5

•

BUTTON «1» (with the engine run-

ning): activation / deactivation.

•

ICON «2»: operating indication icon.

Flashing mode:

- Lit with moving vehicle: the system is working,

but is not active (normal condition).

- Flashing quickly with moving vehicle: The system

is functioning correctly and is active (poor grip con-

ditions, engine power limiting in effect); ride with

extreme care, as the grip limit has been exceeded;

restore the vehicle safety conditions by gently re-

ducing the throttle opening.

- Off with the vehicle in gear:: the system is disa-

bled and will not intervene in case of loss of grip.

•

If the deactivation was voluntary (by

pressing the appropriate button «1» for

1 second with the engine running) it is

recommended to reactivate the system

as soon as possible.

•

If the system was NOT deactivated vol-

untarily, this indicates an ASR system

fault.

To ensure maximum safety of the vehicle it is ad-

visable to keep the system active. Deactivation

may be necessary only in case of starting with very

low grip surfaces (mud, snow) on which the oper-

Pre-delivery

Vespa 946 E4-E5 EMEA-USA-ASIA (2021-)

PRE DE - 10

Содержание 946 E4 EMEA 2021




























































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 946 E4 EMEA 2021

E-Wheels EW-01 Owner'S Manual preview
EW-01
Бренд: E-Wheels Страницы: 16
E-TRENDS FLY Assembly Instructions Manual preview
FLY
Бренд: E-TRENDS Страницы: 15
X-TREME X-250 Instructions preview
X-250
Бренд: X-TREME Страницы: 1
Vectrix VX-2 2011 Service Manual preview
VX-2 2011
Бренд: Vectrix Страницы: 99
Stratasys Bull Rider Assembly Instructions Manual preview
Bull Rider
Бренд: Stratasys Страницы: 24
Denver Electronics SEL-65220 User Manual preview
SEL-65220
Бренд: Denver Electronics Страницы: 21
Scooty CITY 4 Original Instructions Manual preview
CITY 4
Бренд: Scooty Страницы: 20
KOMFI-RIDER KR6000 Deluxe Owner'S Manual preview
KR6000 Deluxe
Бренд: KOMFI-RIDER Страницы: 23
AsVIVA EM2 Manual preview
EM2
Бренд: AsVIVA Страницы: 30
FREERIDER FR168-4S User Instruction Manual preview
FR168-4S
Бренд: FREERIDER Страницы: 44
M SCOOTER S1 Original Instruction User Manual preview
S1
Бренд: M SCOOTER Страницы: 38
X-TREME scooter X-360 Product Handbook preview
X-360
Бренд: X-TREME scooter Страницы: 14
EOVOLT Confort Manual preview
Confort
Бренд: EOVOLT Страницы: 24
e-way E-600MAX User Manual preview
E-600MAX
Бренд: e-way Страницы: 156
OCEAN DRIVE S9 Instruction Manual preview
S9
Бренд: OCEAN DRIVE Страницы: 94
Ugo UGO SQUBBY 8" User Manual preview
UGO SQUBBY 8"
Бренд: Ugo Страницы: 22
Jamara Laufrad Holz Roller Instruction preview
Laufrad Holz Roller
Бренд: Jamara Страницы: 4
Radio Flyer Color FX EZ Glider Manual preview
Color FX EZ Glider
Бренд: Radio Flyer Страницы: 6

Бренды по названию

Популярные бренды

Загрузить еще бренды