VESPA 946 E4 EMEA 2021 Скачать руководство пользователя страница 247

Страница: 247 / 283

- The replacement must be made with greater re-

sidual thickness if the pad has not worn evenly.

A 0.5 mm thickness difference in the residual fric-

tion material is permitted

Refitting

- Insert the brake pads.

- Insert the fixing pin being careful to position the clip with the ends towards the bleed screw.

- Insert the locking on the pin.

- Fix the brake calliper to the bracket and tighten the screws to the specified torque.

CAUTION

BEFORE USING THE BRAKE, OPERATE THE LEVER A FEW TIMES.

Locking torques (N*m)

Rear brake calliper tightening screw

20 - 25 Nm

Fill

Rear - combined

- Remove the rubber cap from the bleed screw.

- Insert a rubber pipe in the bleed screw to permit

the brake fluid to be recovered.

- With the brake lever, load the system and bring

it up to the required pressure.

- Keeping the brake lever pulled, loosen the bleed

screw to purge the air in the system. Then tighten

the bleed screw

- Repeat the operation until only brake fluid comes

out of the rubber pipe.

- Remove the fluid recovery pipe and refit the rub-

ber cap over the bleed screw.

- Top up the brake fluid to the right level in the res-

ervoir. If necessary, bleeding can be done using a

special vacuum pump

Vespa 946 E4-E5 EMEA-USA-ASIA (2021-)

Braking system

BRAK SYS - 247

Содержание 946 E4 EMEA 2021




























































































































































































































































































Результаты поиска

Содержание 946 E4 EMEA 2021

Отзывы:

Похожие инструкции для 946 E4 EMEA 2021

Бренды по названию

Популярные бренды

VESPA 946 E4 EMEA 2021, Руководство пользователя

Результаты поиска

Содержание 946 E4 EMEA 2021

Отзывы:

Похожие инструкции для 946 E4 EMEA 2021

Бренды по названию

Популярные бренды