manualshive.com logo in svg

VESPA 946 E4 EMEA 2021, Руководство пользователя


Поделиться
Скачать
background image

THE ASR SYSTEM IS ACTIVATED AT EVERY "ON" POSI-
TIONING OF THE IGNITION SWITCH.
IF DISABLED BY THE USER, THE ASR SYSTEM KEEPS
THE STATE OF INACTIVITY ONLY IF THE VEHICLE IS OFF,
BY USING THE ENGINE STOP SWITCH; AT THE NEXT KEY
ON THE ASR SYSTEM IS ENABLED AUTOMATICALLY.

CAUTION

IT IS EMPHASISED THAT THE RIDING AUXILIARY SYS-
TEM CANNOT CHANGE THE PHYSICAL LIMITS OF GRIP
AND IS NOT A SUBSTITUTE FOR PROPER MANAGEMENT
OF POWER, BOTH ON STRAIGHT STRETCHES AND IN
TURNS. THEREFORE, IT IS RECOMMENDED TO ALWAYS
USE THE VEHICLE WITH THE UTMOST CARE AND IN AC-
CORDANCE WITH THE REGULATIONS IN FORCE.

CAUTION

AT LOW SPEED, LESS THAN 5 Km/h (3 mph),

 

THE ASR

SYSTEM IS NOT OPERATIONAL.
IT IS RECOMMENDED TO PAY PARTICULAR ATTENTION
IN THE EVENT OF ACCELERATION FROM STANDSTILL IN
CONDITIONS OF LOW GRIP, ESPECIALLY IN THE FIRST
METRES.

N.B.

IN CASE OF ROAD DISCONNECTIONS THERE COULD BE
SHORT ACTIVATIONS OF THE ASR SYSTEM. SUCH
EVENT APPEARS UNDER NORMAL OPERATION CONDI-
TIONS OF THE VEHICLE.

N.B.

THE DEVICE PREVENTS IMPRESSING ON THE REAR
HIGH SPEED ROTATION WHEEL WITH THE VEHICLE ON
THE CENTRE STAND. IT IS RECOMMENDED NOT TO IN-
SIST WITH THE THROTTLE GRIP IN THIS PARTICULAR
CONDITION.

CAUTION

A POOR STATE OF MAINTENANCE OF THE TYRES CAN
RESULT IN ABNORMAL OPERATION OF THE ASR SYS-
TEM.
IN CASE OF REPEATED INTERVENTIONS OF THE ASR,
EVEN ON ROAD SURFACES WITH GOOD GRIP OR SMALL
THROTTLE OPENINGS, IT IS NECESSARY TO CHECK FOR
WEAR AND/OR THE STATE OF INFLATION OF TYRES
FIRST.

CAUTION

IN THE EVENT OF MALFUNCTION OF THE BATTERY, THE
ABS - ASR SYSTEM TURNS OFF.

ASR SYSTEM CALIBRATION PROCEDURE (For the EURO 5 version).

In order to maintain the effectiveness of the ASR system following the replacement of one or both tyres

a calibration procedure of the system must be performed as follows on a straight flat stretch of road.

Vespa 946 E4-E5 EMEA-USA-ASIA (2021-)

Braking system

BRAK SYS - 237

Содержание 946 E4 EMEA 2021




























































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 946 E4 EMEA 2021

Daymak Tokyo User Manual preview
Tokyo
Бренд: Daymak Страницы: 27
Daymak Rickshaw King Manual preview
Rickshaw King
Бренд: Daymak Страницы: 19
Daymak Hamilton User Manual preview
Hamilton
Бренд: Daymak Страницы: 27
Daymak Kingston User Manual preview
Kingston
Бренд: Daymak Страницы: 27
Yolo Electric Bolt Owner'S Manual preview
Bolt
Бренд: Yolo Electric Страницы: 20
Helge Nyberg Ergobjorn User Manual preview
Ergobjorn
Бренд: Helge Nyberg Страницы: 13
Jetson Hex Manual preview
Hex
Бренд: Jetson Страницы: 24
5th Wheel G1 pro User Manual preview
G1 pro
Бренд: 5th Wheel Страницы: 79
Dillenger OPIA User Manual preview
OPIA
Бренд: Dillenger Страницы: 26
MINIMOTO ATV Instruction Manual preview
ATV
Бренд: MINIMOTO Страницы: 31
Skywalker 6.5" Sky Walker User Manual preview
6.5" Sky Walker
Бренд: Skywalker Страницы: 20
Group Vertical Self-Balancing Scooter User Manual preview
Self-Balancing Scooter
Бренд: Group Vertical Страницы: 21
Vermeiren Sedna Instruction Manual preview
Sedna
Бренд: Vermeiren Страницы: 216
E-Wheels E2S V2 User Manual preview
E2S V2
Бренд: E-Wheels Страницы: 70
Baja motorsports RT150 Owner'S Manual preview
RT150
Бренд: Baja motorsports Страницы: 43
Daymak Boomerbeast Ultimate User Manual preview
Boomerbeast Ultimate
Бренд: Daymak Страницы: 18
Cannondale 2014 MAVARO Supplemental Owner'S Manual preview
2014 MAVARO
Бренд: Cannondale Страницы: 25
Razor Kobalt Owner'S Manual preview
Kobalt
Бренд: Razor Страницы: 32

Бренды по названию

Популярные бренды

Загрузить еще бренды