VESPA 946 E4 EMEA 2021 Скачать руководство пользователя страница 207

Страница: 207 / 283

Switch to «

» and check that, with the injector

disconnected and the control unit connected, there

is a voltage present between the Black-Green ca-

ble of the injector connector and earth.

With injector disconnected and the injector load relay disconnected, check the continuity of the Black-

Green cable between the injector connector and relay base.

Inspecting the injector hydraulics

- Remove the engine from the vehicle as described in the corresponding chapter.

- Remove the injector by unscrewing the screw fixing the injector to the head.

Install the specific tool to check the fuel pressure

and position the manifold on a graduated container

of at least 100 cm³.

Connect the injector to the wire supplied with the

injection tester.

Connect the clamps of the cable to an auxiliary

battery.

Activate the fuel pump with the active diagnosis.

Check that, within fifteen seconds, approximately

40 cm³ of fuel is dispensed with an adjustment

pressure of approximately 2.5 Bar.

Specific tooling

020480Y

Fuel pressure measurement kit

Tachometer

Disconnect the fuel pipe connector. Start up the engine and wait for it to stop. With the wiring connected

to the control unit and system try to start up the engine and check that the voltage between pin 20 and

29 is around 2.8 V

- Check the continuity between pin 29 of the injection control unit and the red cable of the engine speed

sensor.

- Check the continuity between pin 20 of the injection control unit and the brown cable of the engine

speed sensor.

Vespa 946 E4-E5 EMEA-USA-ASIA (2021-)

Injection

INJEC - 207

Содержание 946 E4 EMEA 2021




























































































































































































































































































Результаты поиска

Содержание 946 E4 EMEA 2021

Отзывы:

Похожие инструкции для 946 E4 EMEA 2021

Бренды по названию

Популярные бренды

VESPA 946 E4 EMEA 2021, Руководство пользователя

Результаты поиска

Содержание 946 E4 EMEA 2021

Отзывы:

Похожие инструкции для 946 E4 EMEA 2021

Бренды по названию

Популярные бренды