VESPA 946 E4 EMEA 2021 Скачать руководство пользователя страница 180

Страница: 180 / 283

Inspecting the crankshaft plain bearings

- To obtain a good bushing lubrication it is neces-

sary to have both an optimal lubricating pressure

(3.2 bar) and a good oil flow rate; the bushings

must be correctly positioned so as not to obstruct

the oil supply channels.

- The main bushings are comprised of two half-

bearings, one with holes and channels for lubrica-

tion whereas the other is solid.

Characteristic

«A»

AXIS CYLINDER

- The oil feeding channel section is also affected by the bushings driving depth compared with the

crankshaft axial clearance of the limiting surface.

N.B.

TO MEASURE WEAR LIMITS AND COUPLING CLEARANCES, SEE THE SPECIFICATIONS CHAP-
TER.

See also

Crankcase - crankshaft - connecting rod

Coupling chart

N.B.

TO MEASURE WEAR LIMITS AND COUPLING CLEARANCES, SEE THE SPECIFICATIONS CHAP-
TER.

See also

Crankcase - crankshaft - connecting rod

Refitting the crankcase halves

- Follow the removal steps but in reverse order; be

careful to respect the prescribed tightening tor-

ques.

- Insert the by-pass.

- Insert a new gasket and be careful with the align-

ment dowels.

- Maintaining the crankshaft inserted in the fly-

wheel side crankcase, couple the crankcase

halves.

- Insert the screws and tighten to specified torque.

Engine

Vespa 946 E4-E5 EMEA-USA-ASIA (2021-)

ENG - 180

Содержание 946 E4 EMEA 2021




























































































































































































































































































Результаты поиска

Содержание 946 E4 EMEA 2021

Отзывы:

Похожие инструкции для 946 E4 EMEA 2021

Бренды по названию

Популярные бренды

VESPA 946 E4 EMEA 2021, Руководство пользователя

Результаты поиска

Содержание 946 E4 EMEA 2021

Отзывы:

Похожие инструкции для 946 E4 EMEA 2021

Бренды по названию

Популярные бренды