VESPA 946 E4 EMEA 2021 Скачать руководство пользователя страница 128

Страница: 128 / 283

Removal of the engine from the vehicle

- Remove the right and left side fairings.

- Remove the battery cover.

- Remove the complete silencer.

- Remove the air filter.

- Remove the rear mudguard.

- Adequately support the rear part of the vehicle

and unscrew the screw fixing the shock absorber

strut to the bracket on the crankcase.

CAUTION

SUPPORT THE VEHICLE ADEQUATELY.

WARNING

CARRY OUT THESE OPERATIONS WHEN THE ENGINE IS
COLD.

- Remove the pin connecting the swinging arm to

the engine by unscrewing the nut on the left side

of the vehicle.

- Lift the rear part of the vehicle as far as possible.

CAUTION

DURING THE LIFTING OPERATIONS, PAY ATTENTION
THAT THE CABLE HARNESS, TRANSMISSIONS AND
PIPES ARE NOT TIGHTENED.

WARNING

PAY ATTENTION TO THE STABILITY OF THE VEHICLE.

Disconnect the stator and pick-up connectors.

Engine from vehicle

Vespa 946 E4-E5 EMEA-USA-ASIA (2021-)

ENG VE - 128

Содержание 946 E4 EMEA 2021




























































































































































































































































































Результаты поиска

Содержание 946 E4 EMEA 2021

Отзывы:

Похожие инструкции для 946 E4 EMEA 2021

Бренды по названию

Популярные бренды

VESPA 946 E4 EMEA 2021, Руководство пользователя

Результаты поиска

Содержание 946 E4 EMEA 2021

Отзывы:

Похожие инструкции для 946 E4 EMEA 2021

Бренды по названию

Популярные бренды